Lightolier IS:LCAWTSX 产品宣传页
CAUTION: Please read these instructions before installing the luminaire. To avoid electric shock, turn off the power from the electric panel before beginning. For safety, this
luminaire must be grounded. Consult an electrician to make sure all the requirements of the US or Canadian Code for electricity and the current local regulations comply.
luminaire must be grounded. Consult an electrician to make sure all the requirements of the US or Canadian Code for electricity and the current local regulations comply.
Keep these
instructions as reference.
IMPORTANT: Do not expose this luminaire to a room ambient temperature more
than 28°C. An overheating of this luminaire could reduce the performance and the
time life os the light-emitting diode (LED).
than 28°C. An overheating of this luminaire could reduce the performance and the
time life os the light-emitting diode (LED).
Note: This luminaire uses a LED (Light Emitting Diode) light source,
no maintenance is required.
no maintenance is required.
A. ONE-CIRCUIT TRACK INSTALLATION:
1. Align adapter lever open on bead side. (Fig.2 & 3)
2. Align locking lever 60° counter-clockwise. (Fig.3)
3. Insert luminaire module into the track. (Fig.4)
4. Turn adapter lever clockwise. (Fig.4)
5. Turn locking lever 60°. (Fig.4)
1. Align adapter lever open on bead side. (Fig.2 & 3)
2. Align locking lever 60° counter-clockwise. (Fig.3)
3. Insert luminaire module into the track. (Fig.4)
4. Turn adapter lever clockwise. (Fig.4)
5. Turn locking lever 60°. (Fig.4)
B. DOUBLE-CIRCUIT INSTALLATION:
1. Lift brass contact tab approximately ¼ in. (7mm). (Fig.5)
2. Follow previous steps 1-5.
1. Lift brass contact tab approximately ¼ in. (7mm). (Fig.5)
2. Follow previous steps 1-5.
C. FOR DMX CONTROL:
1. Simply connect data cable shielded CAT5 recommended into DMX connector or
1. Simply connect data cable shielded CAT5 recommended into DMX connector or
insert RJ45e jack connector. (Fig.6)
2. For daisy chain data connection, connect data cable CAT5 into data-in socket of
the first luminaire, then connect the data cable to the data-out connector jack of
the next luminaire and so on. (Fig.7)
the next luminaire and so on. (Fig.7)
3. For signal termination, connect a DMX signal terminator to the data out of the
last luminaire in the network. (sold separately). (Fig.8)
Note: Hardware required for DMX control system. (not supplied)
Controller: DMX512 protocol.
Wiring: Use low-capacitance shielded twisted-pair stranded cables such as
Wiring: Use low-capacitance shielded twisted-pair stranded cables such as
EIA485 (RS485) or shielded CAT5.
- 24AWG: maximum run length of 300 m (1000 ft).
- 22AWG: maximum run length of 500 m (1600 ft).
Note: Using unshielded cable may create noise in the system and may cause
undesirable light output.
Connectors: RJ45e connector – 8 conductors (connections: T568B).
Installation Instructions for Lytespan Track LED DMX Control
Accent Lighting Colorspot Luminaire
BEAD
FIG.1
FIG.2
FIG.3
ADAPTER
LEVER
INTERLOCKING LEVER
TRACK
ADAPTER
LEVER
LUMINAIRE MODULE
TRACK
FIG.4
BRASS CONTACT
FIG.5
ADAPTER
LEVER
LOCKING LEVER
WARNING: This luminaire is for ceiling installation on Lytespan track only. Do not install on Monopoint, Multipoint, Fast Track, Sloped Ceiling Adapter, Extension Wand or ProSpec
Track.
Track.
FIG.6
FIG.7
FIG.8
DATA-IN SOCKET
RJ45e PLUG
RJ45e PLUG
RJ45e PLUG
DATA-OUT SOCKET
DMX TERMINATOR
Lightolier is a Philips group brand
IS:LCAWTSX
10-08/Rev-01
Canlyte 3015, Louis Amos, Lachine, Québec H8T 1C4 - Tel.: (514) 636-0670 - Fax.: (514) 636-0460 - www.canlyte.com
Lightolier 631 Airport Road, Fall River, MA 02720, - Tel.: (508) 679-8131 - Fax.: (508) 674-4710 - www.lightolier.com