Lightolier IS:HC356 产品宣传页
A
COMPANY
631 Airport Road, Fall River, MA 02720
IMPORTANT PRECAUTIONS:
Keep your work area clean and well lit. Observe all safety precautions and instructions provided with
the power tool with which you use this hole cutter. This tool is designed to be used with a 3/8” chuck or larger drill. Underpowered tools,
such as a cordless drill with a partially charged battery, may cause the tool to bind, causing ‘kick-back’ or to cut roughly or unevenly. Keep
tool perpendicular to the surface to be cut and apply light even cutting pressure to the material to help prevent unacceptable results.
Maintain sharp cutting bits. Dull bits require more force to cut and may result in tool binding and rough or unevenly cut holes.
1
ADJUST CUTTING BITS TO DESIRED HOLE SIZE:
Each Lightolier Frame-In-Kit has a recommended ceiling opening size. These may be found on
the installation instruction sheet for each product. You may wish to adjust the standard ceiling
opening recommendation based on your own experience and circumstances.
the installation instruction sheet for each product. You may wish to adjust the standard ceiling
opening recommendation based on your own experience and circumstances.
Hole cutter must be removed from drill before adjusting.
This minimizes the risk of injury due to accidental starting of the drill.
To set the cutting blades to cut the desired diameter:
A setup disk is provided with each tool. Place the center hole of the setup disk onto the pilot
drill of the tool. Loosen the small wing nuts on top of both blade holder assemblies, slide each
blade holder so that both cutters pass through the appropriate holes for the Frame-In-Kit you
are installing, retighten the wing nuts.
Alternatively, The Hole Cutter is marked in both inch (1/8”) and metric (5mm) scales. Adjust so
that the inside edge of the blade holder assembly is aligned to the desired dimension on the
marked scale. Check the actual cutting diameter set by measuring from the outside edge of one
blade to the outside edge of the other. (Note: the pilot hole drill should be centered between the
cutting blades.) Make a test cut in a scrap piece of material. If the diameter cut is not exactly
what you want, readjust the blade holder subassemblies as necessary.
drill of the tool. Loosen the small wing nuts on top of both blade holder assemblies, slide each
blade holder so that both cutters pass through the appropriate holes for the Frame-In-Kit you
are installing, retighten the wing nuts.
Alternatively, The Hole Cutter is marked in both inch (1/8”) and metric (5mm) scales. Adjust so
that the inside edge of the blade holder assembly is aligned to the desired dimension on the
marked scale. Check the actual cutting diameter set by measuring from the outside edge of one
blade to the outside edge of the other. (Note: the pilot hole drill should be centered between the
cutting blades.) Make a test cut in a scrap piece of material. If the diameter cut is not exactly
what you want, readjust the blade holder subassemblies as necessary.
2
ATTACH DUST SHIELD:
Loosen and remove the large wing nut (D) from the main shaft (B) of the cutting tool. (Note: the
large wing nut and cutting tool shaft are threaded with Left Hand Threads to prevent them from
loosening during use. Correct direction for loosening is marked on the large wing nut.)
Remove the spring (C) from the main shaft of the cutting tool. Slide the dust shield (A)
assembly over the main shaft of the cutting tool so that the pilot drill (E) and cutting blades (F)
are inside the dust shield. Position the dust shield firmly against the cutting tool shoulder,
replace the spring and the large wing nut (remember this is a left hand thread). Tension on the
dust shield may be adjusted by positioning the large wing nut. The closer to the dust shield you
position the wing nut, the more tension there will be on the dust shield.
large wing nut and cutting tool shaft are threaded with Left Hand Threads to prevent them from
loosening during use. Correct direction for loosening is marked on the large wing nut.)
Remove the spring (C) from the main shaft of the cutting tool. Slide the dust shield (A)
assembly over the main shaft of the cutting tool so that the pilot drill (E) and cutting blades (F)
are inside the dust shield. Position the dust shield firmly against the cutting tool shoulder,
replace the spring and the large wing nut (remember this is a left hand thread). Tension on the
dust shield may be adjusted by positioning the large wing nut. The closer to the dust shield you
position the wing nut, the more tension there will be on the dust shield.
Do not operate this tool without the Dust Shield installed.
The shield helps protects the user from injury by contact
with sharp cutters and other rotating components.
3
POSITION TOOL: Always wear eye protection when operating tool.
Attach the hole cutting tool to your drill and tighten drill chuck securely. Mark the center of the
hole you want to cut on your ceiling, gypsum board or ceiling tile. Align the drill at the center of
the cutting tool to the center mark. Keep the tool perpendicular to the surface to be cut and drill
the center pilot hole. While drilling, the dust shield will eventually contact the work surface,
containing the dust from cutting as well as providing support so that the cutting tool is held
perpendicular to the cutting surface. As the cutting blades contact the surface to be cut adjust
your cutting speed and pressure applied as necessary to achieve a clean, smooth cut.
hole you want to cut on your ceiling, gypsum board or ceiling tile. Align the drill at the center of
the cutting tool to the center mark. Keep the tool perpendicular to the surface to be cut and drill
the center pilot hole. While drilling, the dust shield will eventually contact the work surface,
containing the dust from cutting as well as providing support so that the cutting tool is held
perpendicular to the cutting surface. As the cutting blades contact the surface to be cut adjust
your cutting speed and pressure applied as necessary to achieve a clean, smooth cut.
READ AND UNDERSTAND THESE INSTRUCTIONS FULLY.
Failure to follow all instructions can result in damage to the tool, damage to the material
and/or serious personal injury. Dust mask, non-skid safety shoes, hard hat and hearing
and/or serious personal injury. Dust mask, non-skid safety shoes, hard hat and hearing
protection must be used for appropriate conditions. Do not overreach. Keep proper
footing and balance at all times particularly when operating tools overhead.
Always wear eye protection.
Use proper safety equipment.
Retain these instructions for future reference.
Clean tool with damp cloth only – do not submerge or place under running water.
WARNING:
SHOCK HAZARD –
DO NOT USE NEAR LIVE ELECTRICAL CIRCUITS.
INSTRUCTION SHEET NO.
IS: HC356
A0407
Page 1 of 1
1
WARNING:
HEALTH HAZARD –
SOME DUST CREATED BY USE OF THIS TOOL AND OTHER CONSTRUCTION
ACTIVITIES, MAY CONTAIN HAZARDOUS MATERIALS SUCH AS LEAD OR ASBESTOS. WORK IN A WELL VENTILATED AREA
AND USE APPROVED SAFETY EQUIPMENT SUCH AS DUST MASKS TO MINIMIZE EXPOSURE TO THESE MATERIALS.