Lightolier LSB-1 产品宣传页
Job Information
Type:
Job Name:
Cat. No.:
Lamp(s):
Notes:
"JSQPSU3PBE
'BMM3JWFS
."t
t'BY
We reserve the right to change details of design, materials and finish.
XXXMJHIUPMJFSDPN½1IJMJQT(SPVQt
We reserve the right to change details of design, materials and finish.
XXXMJHIUPMJFSDPN½1IJMJQT(SPVQt
Lighting Systems
LSB-1
1BHFPG
-ZUFTQSFBEÜ-4#4PMJE*OEJSFDU-JHIU51FS'PPU /PNJOBM
4FDUJPO
#
Features
1. Housing: Extruded aluminum. Die-cast end-cap mechanically attached with
no exposed fasteners or hardware.
2. Lamping: One T5, 28 or 54 watt (as specified) fluorescent lamp per 4-Foot
nominal section. Provided by others.
3. Reflector: Precision die-formed semi-specular aluminum.
Electrical
Ballast is <10% THD, .98 ballast factor, pre-heat start. 18 gauge wire. Color-
coded quick connectors allow ease of connection for joiner modules. Power feed
is 18 gauge white SJT. For special circuiting consult factory. Factory installed
ballast disconnect allows the ballast to be disconnected from and reconnected to
incoming power under load without turning the entire circuit off.
coded quick connectors allow ease of connection for joiner modules. Power feed
is 18 gauge white SJT. For special circuiting consult factory. Factory installed
ballast disconnect allows the ballast to be disconnected from and reconnected to
incoming power under load without turning the entire circuit off.
Dimming: 120/277 VAC 1% dimming level, 4 wire feed required.
Emergency Battery Pack: 28 watt: 520 lumens @ 90 minutes, 54 watt: 700
lumens @ 90 minutes.
lumens @ 90 minutes.
Mountings
Finish
Powder coated baked white or aluminum finish. Custom colors available, consult
factory.
factory.
Options and Accessories
Emergency circuiting; special circuiting; X, T & L joiner blocks - consult factory.
Ordering Information
Family
Lamps
Voltage
Finish
1 = 1-Lamp T5
4 = 4-Foot
A = Solid
28 = 28W T5
AL = Aluminum
8 = 8-Foot
54 = 54W T5
WH = White
5E = 54W T5 Emergency Pack
2E = 28W T5 Emergency Pack
5D = 54W T5 Dimming
2E = 28W T5 Emergency Pack
5D = 54W T5 Dimming
LSB
1
A
Length
Shielding
Ballast
1 = 120 volt
2 = 277 volt
2 = 277 volt
Cable suspension (not shown) - 4-1/2" (11.43cm) diameter canopy finished white
enamel, 1/16" (0.16cm) diameter stainless steel aircraft cable adjustable up to 36"
(91.44cm). Dual-screw draw-tight connector to create hairline seam between joiner
modules.
enamel, 1/16" (0.16cm) diameter stainless steel aircraft cable adjustable up to 36"
(91.44cm). Dual-screw draw-tight connector to create hairline seam between joiner
modules.
Complete ordering instructions below.
Labels
UL, cUL and I.B.E.W.
Ordering Instructions
Individual Fixtures:
1. Order number of MODULES required.
2. Order one POWER FEED END SET per MODULE.
1. Order number of MODULES required.
2. Order one POWER FEED END SET per MODULE.
Continuous Rows:
1. Determine run length.
2. Order the appropriate number of MODULES for the complete run.
3. Order one POWER FEED END SET per run.
4. Order one CABLE ASSEMBLY per MODULE minus one per run.
5. For runs that exceed amperage limits, order the appropriate
1. Determine run length.
2. Order the appropriate number of MODULES for the complete run.
3. Order one POWER FEED END SET per run.
4. Order one CABLE ASSEMBLY per MODULE minus one per run.
5. For runs that exceed amperage limits, order the appropriate
number of CABLE/CORD ASSEMBLIES.
Fixture Shown Half Scale
2
1
3
8-1/2” (21.59cm)
1-3/4" (4.45cm)