Lightolier LSB-7 产品宣传页
Job Information
Type:
Job Name:
Cat. No.:
Lamp(s):
Notes:
"JSQPSU3PBE
'BMM3JWFS
."t
t'BY
We reserve the right to change details of design, materials and finish.
XXXMJHIUPMJFSDPN½1IJMJQT(SPVQt
We reserve the right to change details of design, materials and finish.
XXXMJHIUPMJFSDPN½1IJMJQT(SPVQt
Lighting Systems
LSB-7
1BHFPG
-ZUFTQSFBEÜ-4#1JFSDFE-VNJOPVT*OEJSFDU-JHIU51FS'PPU /PNJOBM
4FDUJPO
#
Features
1. Housing: Extruded aluminum. Die-cast end cap mechanically attached with
no exposed fasteners or hardware.
2. Lamping:
nominal section. Provided by others.
3. Reflector: Precision die-formed semi-specular aluminum.
4. Shielding: Precision die-formed, pierced 20 gauge CRS. Piercing is four rows
4. Shielding: Precision die-formed, pierced 20 gauge CRS. Piercing is four rows
that extend the entire length of the lamps. The pattern is 5/8” (1.59cm) x 1/16”
(0.16cm) slot with a 3/16” (0.48cm) separation between rows.
(0.16cm) slot with a 3/16” (0.48cm) separation between rows.
Electrical
Ballast is <10% THD, .98 ballast factor, pre-heat start. 18 gauge wire. Color-
coded quick connectors allow ease of connection for joiner modules. Power feed
is 18 gauge white SJT. For special circuiting consult factory. Factory installed
ballast disconnect allows the ballast to be disconnected from and reconnected to
incoming power under load without turning the entire circuit off.
coded quick connectors allow ease of connection for joiner modules. Power feed
is 18 gauge white SJT. For special circuiting consult factory. Factory installed
ballast disconnect allows the ballast to be disconnected from and reconnected to
incoming power under load without turning the entire circuit off.
Dimming: 120/277 VAC 1% dimming level, 4 wire feed required.
Emergency Battery Pack: 28 watt: 520 lumens @ 90 minutes, 54 watt: 700
lumens @ 90 minutes, 4 wire feed required.
lumens @ 90 minutes, 4 wire feed required.
Mountings
Finish
Powder coated baked white or aluminum finish. Custom colors available, consult
factory.
factory.
Labels
UL, cUL and I.B.E.W.
Ordering Instructions
Individual Fixtures:
1. Order number of MODULES required.
2. Order one POWER FEED END SET per MODULE.
1. Order number of MODULES required.
2. Order one POWER FEED END SET per MODULE.
Continuous Rows:
1. Determine run length.
2. Order the appropriate number of MODULES for the complete run.
3. Order one POWER FEED END SET per run.
4. Order one CABLE ASSEMBLY per MODULE minus one per run.
5. For runs that exceed amperage limits, order the appropriate number of
1. Determine run length.
2. Order the appropriate number of MODULES for the complete run.
3. Order one POWER FEED END SET per run.
4. Order one CABLE ASSEMBLY per MODULE minus one per run.
5. For runs that exceed amperage limits, order the appropriate number of
CABLE/CORD ASSEMBLIES.
Options and Accessories
Emergency Circuiting; special circuiting; X, T & L joiner blocks - consult factory.
Complete ordering instructions below.
Cable suspension (not shown) - 4-1/2" (11.43cm) diameter canopy finished white
enamel, 1/16" (0.16cm) diameter stainless steel aircraft cable adjustable up to 36"
(91.44cm). Dual-screw draw-tight connector to create hairline seam between joiner
modules.
enamel, 1/16" (0.16cm) diameter stainless steel aircraft cable adjustable up to 36"
(91.44cm). Dual-screw draw-tight connector to create hairline seam between joiner
modules.
Ordering Information
Family
Lamps
Voltage
Finish
3 = 3-Lamp T5
B = Pierced
AL = Aluminum
WH = White
WH = White
LSB
3
B
Length
Shielding
Ballast
1 = 120 volt
2 = 277 volt
2 = 277 volt
28 = 28W T5
54 = 54W T5
5E = 54W T5 Emergency Pack
2E = 28W T5 Emergency Pack
5D = 54W T5 Dimming
54 = 54W T5
5E = 54W T5 Emergency Pack
2E = 28W T5 Emergency Pack
5D = 54W T5 Dimming
Three T5, 28 or 54 watt (as specified) fluorescent lamps per 4-Foot
4 = 4-Foot
8 = 8-Foot
8 = 8-Foot
Pierce Pattern
3-1/2" (8.89cm)
3/16"
(0.48cm)
5/8"
(1.59cm)
3-1/16"
(7.78cm)
(7.78cm)
1/16"
(0.16cm)
(0.16cm)
1
3
4
Fixture Shown Half Scale
2
8-1/2” (21.59cm)
1-3/4" (4.45cm)