Lightolier PTS7-3 产品宣传页
Job Information
Type:
Job Name:
Cat. No.:
Lamp(s):
Notes:
"JSQPSU3PBE
'BMM3JWFS
."t
t'BY
We reserve the right to change details of design, materials and finish.
XXXMJHIUPMJFSDPN½1IJMJQT(SPVQt
We reserve the right to change details of design, materials and finish.
XXXMJHIUPMJFSDPN½1IJMJQT(SPVQt
Lighting Systems
PTS7-3
1BHFPG
1FSJNFUFS5SPVHI3FDFTTFE%JSFDU-PVWFSX"JS$IBOOFM-JHIU51FS'PPU4FDUJPO
#
Sample Run, End Plate and Corner Block Accessories
Quarter Scale
6
5
2
4
3
Complete ordering instructions on back.
Example of Straight Run
Lighted
Telescoping
Unit
84"
84"
60"
Example of Pattern Run
Telescoping
Unit
Unit
90° Inside Corner
48"
60"
48"
(3 places)
135° Outside
PTS7C1350 Standard
PTS7C1350A Air
PTS7C1350 Standard
PTS7C1350A Air
8 -1/2” (245.11cm)
135° Inside
PTS7C1351 Standard
PTS7C1351A Air
PTS7C1351 Standard
PTS7C1351A Air
90° Outside
PTS7C900 Standard
PTS7C900A Air
PTS7C900 Standard
PTS7C900A Air
90° Inside
PTS7C901 Standard
PTS7C901A Air
PTS7C901 Standard
PTS7C901A Air
End Cap Set
PTS7EP Standard
PTS7EPA Air
PTS7EP Standard
PTS7EPA Air
14” (35.56cm)
Features
1.
2. Lamping: One T8 or T12 fluorescent lamp, as specified. Provided by others.
3. Reflector: Die-formed semi-specular aluminum.
4. Louver: Semi-specular anodized aluminum, 40° lengthwise by 30° minimum
3. Reflector: Die-formed semi-specular aluminum.
4. Louver: Semi-specular anodized aluminum, 40° lengthwise by 30° minimum
crosswise shielding. Supported along both edges by concealed frame of
extruded aluminum. Bold baffle, prismatic lens, gold anodized louver, open or
egg crate louver available, consult factory.
extruded aluminum. Bold baffle, prismatic lens, gold anodized louver, open or
egg crate louver available, consult factory.
5. Socket Channels: Die-formed, pre-painted steel held by support brackets and
allows for up to 6” (15.24cm) lamp overlap.
6.
Electrical
Specify 120 volt or 277 volt. 3 conductor, 18 gauge wire. Color-coded quick
connectors allow ease of connection for joiner modules. For special circuiting,
consult factory. Factory installed ballast disconnect allows the ballast to be
disconnected from and reconnected to incoming power under load without turning
the entire circuit off.
Dimming: Advance Mark X, use Advance compatible two-wire control (no extra
control lead required).
connectors allow ease of connection for joiner modules. For special circuiting,
consult factory. Factory installed ballast disconnect allows the ballast to be
disconnected from and reconnected to incoming power under load without turning
the entire circuit off.
Dimming: Advance Mark X, use Advance compatible two-wire control (no extra
control lead required).
7. Air Supply Channel: For air supply or ducted air return. Ducted air return
requires Anemostat #PRTS or equivelant (by others).
Mountings
Wall Adjustment Bracket - Allows for inconsistencies in wall straightness.
Die-formed steel used to mount system to the wall.
Die-formed steel used to mount system to the wall.
Finish
Ceiling trim painted baked enamel semi-gloss white.
Options and Accessories
90° inside, 90° outside, 135° inside, and 135° outside corerns available.
Labels
UL, cUL and I.B.E.W.
11-1/4” (28.58cm)
7 -1/16”
(19.94cm)
1-5/16” (3.33cm)
8-1/4” (20.96cm)
1-1/2” (3.81cm)
1-1/2”
(3.81cm)
(3.81cm)
4-3/4” (12.07cm)
1-1/2” (3.81cm)
Housing: Die-formed steel, slotted for air return. Integral flanges at each end
strengthen the housing and permit housings to be bolted together in continuous
runs and facilitate suspension of fixture. Concealed openings for heat extraction
and air return.
strengthen the housing and permit housings to be bolted together in continuous
runs and facilitate suspension of fixture. Concealed openings for heat extraction
and air return.
Ceiling Trim: Extruded aluminum with integral aligner splines.
90° Outside Corner
7
1
8' 1/2”
(245.11cm)
8' 1/2”
245.11cm
14" (35.56cm)
14" (35.56cm)
10' 2-1/4” (310.52cm)
9' 0” (274.32cm)
21' 10-3/4” (677.39cm)