Lightolier IS:1170 产品宣传页
READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE
This fixture is intended for installation in accordance with the National Electrical Code and local regulations.
To assure full compliance with local codes and regulations, check with your local electrical inspector before
installation. To prevent electrical shock, turn off electricity at fuse box before proceeding.
To assure full compliance with local codes and regulations, check with your local electrical inspector before
installation. To prevent electrical shock, turn off electricity at fuse box before proceeding.
Retain these instructions for maintenance reference.
LIGHTOLIER a GENLYTE company.
631 Airport Road, Fall River, MA 02720
631 Airport Road, Fall River, MA 02720
®
INSTRUCTION SHEET NO.
IS:1170
A0997 Page 1 of 2
INSTALLATION OF 7•11 REFLECTOR TRIM
1. INSTALL FRAME-IN KIT (Fig. A)
See FRAME-IN KIT Instruction Sheet for installation procedure.
2. SNAP-ON (Fig. B)
Insert SOCKET CUP in neck of REFLECTOR. Make sure SPRINGS
of SOCKET CUP snap into SLOTS of REFLECTOR.
of SOCKET CUP snap into SLOTS of REFLECTOR.
3. PUSH UP (Fig. C)
a. Rotate ROTO-CLIPS, if so equipped, for proper REFLECTOR
TRIM size. For 7•11 (white reflectors 1170 Series and 1180
Series) the LONGER LEGS should extend inwardly toward the
opening.
Note: The LONGER LEG has a return on top (Fig. E)
Series) the LONGER LEGS should extend inwardly toward the
opening.
Note: The LONGER LEG has a return on top (Fig. E)
b. Push REFLECTOR TRIM straight up until it is right against
ceiling.
Note: To remove REFLECTOR TRIM, turn REFLECTOR TRIM
counterclockwise while pulling downward. When using 1104
Series Frame-In Kits, squeeze REFLECTOR SPRING from inside
until the TRIM disengages. To retrieve SOCKET CUP, pull on
one of the SOCKET SPRING legs to disengage. (Fig. F)
Note: To remove REFLECTOR TRIM, turn REFLECTOR TRIM
counterclockwise while pulling downward. When using 1104
Series Frame-In Kits, squeeze REFLECTOR SPRING from inside
until the TRIM disengages. To retrieve SOCKET CUP, pull on
one of the SOCKET SPRING legs to disengage. (Fig. F)
DROPPED OPALEX INSTALLATION PROCEDURE
(1178, 1180) (Fig. G)
1. Before installing TRIM into Frame-In Kit, remove Lexan DIFFUSER
by rotating DIFFUSER counterclockwise.
2. Follow instructions 2 and 3 above.
3. Lamp fixture with recommended wattage and bulb type.
4. Replace DIFFUSER by aligning the (3) SLOTS in DIFFUSER with
3. Lamp fixture with recommended wattage and bulb type.
4. Replace DIFFUSER by aligning the (3) SLOTS in DIFFUSER with
the (3) BUMPS in the REFLECTOR, push up and turn clockwise.
WARNING: BEFORE INSTALLING REFLECTOR TO FRAME-IN KIT, READ MARKINGS IN REFLECTOR TRIM AND IN SOCKET CUP
OF FRAME-IN KIT TO DETERMINE LAMP WATTAGE AND TYPE APPLICABLE FOR YOUR INSTALLATION. IF I.C. TYPE FRAMING
KIT IS USED, IT MAY BE INSTALLED IN DIRECT CONTACT WITH INSULATED CEILING. IF A NON I.C. TYPE FRAME-IN KIT IS USED,
DO NOT INSTALL INSULATION WITHIN 3 INCHES OF FIXTURE SIDES OR WIRING COMPARTMENT, NOR ABOVE FIXTURE IN
SUCH A MANNER TO ENTRAP HEAT. FOR I.C. TYPE INSTALLATION ONLY: ASSEMBLE SOCKET CUP IN UPPER SLOT POSITION
FOR REFLECTOR TRIMS WITH DUAL SLOT POSITIONS. (FIG. B)
OF FRAME-IN KIT TO DETERMINE LAMP WATTAGE AND TYPE APPLICABLE FOR YOUR INSTALLATION. IF I.C. TYPE FRAMING
KIT IS USED, IT MAY BE INSTALLED IN DIRECT CONTACT WITH INSULATED CEILING. IF A NON I.C. TYPE FRAME-IN KIT IS USED,
DO NOT INSTALL INSULATION WITHIN 3 INCHES OF FIXTURE SIDES OR WIRING COMPARTMENT, NOR ABOVE FIXTURE IN
SUCH A MANNER TO ENTRAP HEAT. FOR I.C. TYPE INSTALLATION ONLY: ASSEMBLE SOCKET CUP IN UPPER SLOT POSITION
FOR REFLECTOR TRIMS WITH DUAL SLOT POSITIONS. (FIG. B)
Fig. C
PUSH-UP
PUSH-UP
Fig. D
EYEBALL
EYEBALL
Fig. A
INSTALL FRAME-IN KIT
INSTALL FRAME-IN KIT
Fig. B
SNAP-ON
SNAP-ON
NOTE
: Use this Instruction Sheet only when Lytecaster Reflector Trim is being installed in the Lightolier 1100 series Frame-In
Kits. If not, disregard this Instruction Sheet. It is recommended you maintain a copy of the following instructions for reference.
Fig. E
Fig. F
REFLECTOR
SPRING
SPRING
SOCKET SPRING
LEG
LEG
SOCKET
CUP
LONGER LEG
(Points Inward for 7•11
White Reflector Trim)
RETURN
ROTO CLIP
REFLECTOR
DIFFUSER
BUMPS
SLOT
Fig. G