Lightolier IS:49126LS 产品宣传页
WARNING: TO PREVENT ELECTRIC
SHOCK, TURN OFF POWER TO TRACK.
SHOCK, TURN OFF POWER TO TRACK.
631 Airport Road, Fall River, MA 02720
COMPANY
A
READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING LUMINAIRE
This luminaire is intended for installation in accordance with the National Electrical Code and local regulations.
To assure full compliance with local codes and regulations, check with your local electrical inspector before
installation. To prevent electric shock, turn off electricity at fuse box before proceeding.
Retain these instructions for maintenance reference.
IS:49126LS
INSTRUCTION SHEET NO.
A0105
Page 1 of 1
NOTE: Not for use with ProSpec track.
INSTRUCTIONS FOR 9”,12”&16” PENDALYTE™ SERIES TRACK MOUNT TO LYTESPAN ® TRACK SYSTEM
SUSPENSION KITS. FOR USE WITH LYTESPAN TRACK SYSTEMS ONLY.
Note: This instruction sheet covers several luminaire styles. Powerhead assembly, lamp type, and reflector style may vary slightly from that
shown, although installation is the same.
shown, although installation is the same.
CAUTION: MAXIMUM WATTAGE AS MARKED ON LUMINAIRE MUST NOT BE EXCEEDED.
DISC
CAP NUTS
Fig. 4
TAB
TUBE CLIP
DECO
TUBES
TUBES
Fig. 3
SCREW HEAD / LANCED TAB
DIFFUSER DISC INSTALLATION (fig. 4)
1.
1.
Install DECO TUBE assemblies to
POWERHEAD first.
POWERHEAD first.
2.
Align holes in DISC with ends of DECO
TUBES.
TUBES.
POWERHEAD INSTALLATION (fig. 1):
Note: On 9” unit MOUNT PLATE must be oriented correctly to clear DOOR SCREW head (see fig. 1).
Note: On 9” unit MOUNT PLATE must be oriented correctly to clear DOOR SCREW head (see fig. 1).
1.
Attach CABLE ADJUSTER to MOUNT PLATE with PANEL NUT.
2.
Pass POWERCORD through relief bushing hole in MOUNT PLATE.
3.
While supporting POWERHEAD ASSEMBLY wire luminaire using WIRE NUTS (local
hardware item): black luminaire lead to hot (black) POWERCORD lead, white luminaire lead
to neutral (white) POWERCORD lead. Attach luminaire ground wire(s) (green and/or bare) to
green ground wire from POWERCORD.
hardware item): black luminaire lead to hot (black) POWERCORD lead, white luminaire lead
to neutral (white) POWERCORD lead. Attach luminaire ground wire(s) (green and/or bare) to
green ground wire from POWERCORD.
4.
Height adjustment: to raise luminaire push excess POWERCORD down into POWERHEAD.
(Make certain CABLE does not interfere with internal wiring or components, both
POWERCORD and CABLE may be cut inside POWERHEAD. Remove DOOR SCREW and
pull DOOR away from POWERHEAD). CABLE is inserted into CABLE ADJUSTER. Raise
luminaire by providing slack in CABLE and pushing through CABLE ADJUSTER. Lower
luminaire by depressing PLUNGER .
(Make certain CABLE does not interfere with internal wiring or components, both
POWERCORD and CABLE may be cut inside POWERHEAD. Remove DOOR SCREW and
pull DOOR away from POWERHEAD). CABLE is inserted into CABLE ADJUSTER. Raise
luminaire by providing slack in CABLE and pushing through CABLE ADJUSTER. Lower
luminaire by depressing PLUNGER .
5.
Secure POWERCORD to MOUNT PLATE with RELIEF BUSHING.
6.
Attach MOUNT PLATE to
POWERHEAD with 8-32 SCREWS.
POWERHEAD with 8-32 SCREWS.
DECO TUBE INSTALLATION (fig. 3)
1.
1.
Slip bottom of TUBE CLIP over TAB on
bottom of POWERHEAD.
bottom of POWERHEAD.
2.
Pivot top of DECO TUBE assembly until
top of TUBE CLIP snaps over SCREW
HEADS (9” units) or LANCED TABS
(12”&16” units).
top of TUBE CLIP snaps over SCREW
HEADS (9” units) or LANCED TABS
(12”&16” units).
3.
Repeat for remaining tube
CAUTION: MAKE CERTAIN WIRES
ARE NOT PINCHED BETWEEN PARTS.
ARE NOT PINCHED BETWEEN PARTS.
Fig. 2
TRACK
STEM LEVER
BEAD
POWERHEAD
ASSEMBLY
POWERCORD
CABLE
RELIEF
BUSHING
BUSHING
CABLE ADJUSTER
MOUNT
PLATE
PLATE
WIRE NUTS
Fig. 1
8-32 SCREWS
PANEL NUT
DOOR
SCREW
SCREW
DOOR
SUSPENSION
STEM
STEM
POWER
STEM
STEM
INSTALLATION INTO TRACK (fig. 2)
1.
1.
Turn off power to TRACK.
2.
Insert SUSPENSION STEM into track. The STEM LEVER must be on the same
side as the track bead. See fig. 2.
side as the track bead. See fig. 2.
3.
Rotate suspension stem 90° clockwise using STEM LEVER. STEM LEVER
should be parallel to TRACK.
should be parallel to TRACK.
4.
To remove: rotate SUSPENSION STEM 90° counterclockwise using STEM
LEVER.
LEVER.
5.
Repeat steps 2 and 3 with POWER STEM.