Panasonic SC-PTX5 用户手册
RQ
TX00
14
30
Usin
g the
F
M/AM rad
io
Using the FM/AM radio
Radio operations are described mainly with the remote control.
You can alternatively use the corresponding button on the main unit.
You can alternatively use the corresponding button on the main unit.
§1
[SELECTOR]
§2
[
X TUNING W]
§3
[MEMORY]
Up to 30 stations can be set in each band, FM and AM.
∫
If noise is excessive
When “FM” is selected
Press and hold [—FM MODE] on
the main unit to display
the main unit to display
“MONO”.
Press and hold [—FM MODE] again to cancel the mode.
≥ The mode is also canceled when you change the frequency.
≥ The mode is also canceled when you change the frequency.
When “AM” is selected
Press [FUNCTIONS] on the remote control.
Each time you press the button: BP 2
()BP 1
∫
Presetting the channel
Up to 30 stations can be set in each band, FM and AM.
1 While listening to the radio broadcast
1 While listening to the radio broadcast
Press [ENTER]
§3
.
2 While the frequency and “PGM” are flashing on the display
Press the numbered buttons to select a channel.
≥ To select a 2-digit number
≥ To select a 2-digit number
e.g. 12:
[
S10]
➜ [1] ➜ [2]
Alternatively, press [
X, W], and then press [ENTER]
§3
.
A station previously stored is overwritten when another station is
stored in the same channel preset.
stored in the same channel preset.
FM frequency step
\Main\unit\only]
The step is factory-set to 0.2-MHz, but you can change it to receive
broadcasts allocated in 0.1-MHz steps.
1 Press [SELECTOR] to select “FM”.
The step is factory-set to 0.2-MHz, but you can change it to receive
broadcasts allocated in 0.1-MHz steps.
1 Press [SELECTOR] to select “FM”.
2 Press and hold [SELECTOR].
After a few seconds the display changes to show the current minimum
frequency. Continue to hold the button down. The minimum frequency
changes and the step is changed.
After a few seconds the display changes to show the current minimum
frequency. Continue to hold the button down. The minimum frequency
changes and the step is changed.
To return to the original step, repeat steps
1 and 2.
[Note]
After changing the setting, previously preset frequencies will be cleared.
Preset them again.
Preset them again.
Presetting stations automatically
1
Press [TUNER/BAND]
§1
to select “FM” or “AM”.
2
Press and hold [ENTER]
§3
.
Release the button when “FM AUTO” or “AM AUTO” is displayed.
The tuner tunes to the lowest frequency and starts to preset all the
stations it can receive into the channels in ascending order.
≥ “SET OK” is displayed when the stations are set, and the radio
stations it can receive into the channels in ascending order.
≥ “SET OK” is displayed when the stations are set, and the radio
tunes to the last preset station.
≥ “ERROR” is displayed when automatic presetting is unsuccessful.
Preset the channels manually (
➜ right).
Selecting the preset channels
1
Press [TUNER/BAND]
§1
to select “FM” or “AM”.
2
Press the numbered buttons to select the channel.
≥ To select a 2-digit number
e.g. 12: [
S10]
➜ [1] ➜ [2]
Alternatively, press [
X, W].
≥ To perform this step on the main
unit, first press [-TUNE MODE] to select “PRESET”, and then
press [
press [
X TUNING W] to select the channel.
When a stereo FM broadcast is being
received, “ST” lights in the display.
received, “ST” lights in the display.
CM SKIP
FUNCTIONS
ENTER
TUNER/BAND
,
,
Numbered
buttons
SELECTOR
TUNING
MEMORY
-TUNE MODE /
FM MODE
-
DISC S.SRD
TG
KARA D.MIX MONO
SLP
SB
ODE
CD
DVD
Manual tuning
1
Press [TUNER/BAND]
§1
to select “FM” or “AM”.
2
Press [
6, 5]
§2
to select the frequency.
≥ When performing this step on the main unit, first press
[-TUNE MODE] to select “MANUAL”, and then press [
X TUNING W]
to select the frequency.
≥ To start automatic tuning, press and hold [6, 5] until the
frequency starts scrolling. Tuning stops when a station is found.
DISC S.SRD
TG
KARA D.MIX MONO
SLP
PTX5.book Page 30 Thursday, May 10, 2007 4:39 PM