Panasonic SA-BTX70 用户手册
10
RQT9479
Connections to a Set Top Box, etc.
Use the following connections when you want to output the original surround audio from your Set Top Box, cable TV, VCR, DVD recorder, etc.
through this unit’s speakers.
≥Do not connect through the video cassette recorder.
through this unit’s speakers.
≥Do not connect through the video cassette recorder.
Due to copy guard protection, the picture may not be displayed properly.
≥Turn off all equipment before connection.
Radio antenna connections
≥Keep loose antenna cables away from other wires and cables.
OPTICAL
OUT
OPTICAL 2(STB)
TV
Optical digital
audio cable
(not included)
audio cable
(not included)
STB, VCR,
DVD recorder, etc.
DVD recorder, etc.
Refer to the operating
instructions of the respective
devices for the optimal
connections.
instructions of the respective
devices for the optimal
connections.
Main unit
≥This unit can decode the surround signal from the Set Top
Box (Satellite receiver, Cable box, etc.).
Press [EXT-IN] several times to select “D-IN 2”
(DIGITAL IN 2*).
* “(CABLE/SAT)” is displayed next to DIGITAL IN 2 when
(DIGITAL IN 2*).
* “(CABLE/SAT)” is displayed next to DIGITAL IN 2 when
set for CABLE/SAT AUDIO input. (
> 25, Setting the TV
audio for VIERA Link “HDAVI Control”)
≥For connections between this unit and the TV, refer to “TV
connections”. (
> 9)
≥If you have various sound sources and this unit’s
terminals are not sufficient, connect them to the available
inputs on the TV and the TV output should then be
connected to the “AUX” or “OPTICAL 1(TV)” terminal of
the main unit.
Refer to the operating instructions of the TV, video
cassette recorder, DVD recorder or Set Top Box for
settings to output its audio via AUDIO OUT or OPTICAL
OUT terminal of the TV.
– In some cases the audio signal will only be output as
inputs on the TV and the TV output should then be
connected to the “AUX” or “OPTICAL 1(TV)” terminal of
the main unit.
Refer to the operating instructions of the TV, video
cassette recorder, DVD recorder or Set Top Box for
settings to output its audio via AUDIO OUT or OPTICAL
OUT terminal of the TV.
– In some cases the audio signal will only be output as
2ch audio from the TV. In this case, connect the Set Top
Box (Satellite receiver, Cable box, etc.) that will be used
most commonly with multi-channel audio to this unit’s
“OPTICAL 2(STB)” terminal.
Box (Satellite receiver, Cable box, etc.) that will be used
most commonly with multi-channel audio to this unit’s
“OPTICAL 2(STB)” terminal.
TIPS
FM
ANT
75
Ω
Main unit
FM Indoor antenna
1
Using an FM indoor antenna
Using an FM outdoor antenna
Use outdoor antenna if FM radio reception is poor.
Use outdoor antenna if FM radio reception is poor.
≥Disconnect the antenna when the unit is not in use.
≥Do not use the outdoor antenna during an electrical storm.
Main unit
FM
ANT
75
FM
ANT
75
Antenna plug (not included)
75 Ω
coaxial cable*
(not included)
FM outdoor antenna
[Using a TV antenna (not included)]
The antenna should be installed by a
competent technician.
[Using a TV antenna (not included)]
The antenna should be installed by a
competent technician.
Main unit
Adhesive
tape
tape
FM indoor antenna (included)
Affix this end of the antenna
where reception is best.
Affix this end of the antenna
where reception is best.
1
*
Rework your outdoor antenna’s 75 Ω
coaxial cable as follows.
7 mm (
9
/
32
)
10 mm (
13
/
32
)
Peel back
10 mm (
13
/
32
)
Remove a piece of the
outer vinyl insulator.
outer vinyl insulator.
Carefully pull the tabs
apart to remove the cover.
Attach the cover.
Install the coaxial cable.
Clamp the cable conductor,
and wind it on so that it does
not contact anything else.
and wind it on so that it does
not contact anything else.
Clamp with pliers
Ω
Ω
Getting s
tar
te
d
BTX70PP_eng.book 10 ページ ２００９年６月２４日 水曜日 午後３時４２分