Mitsumi electronic 738 Series 用户手册
76
Appendices
For assistance call 1(800) 332-2119
Programming the Remote Control
Press one of the upper buttons on the remote
1.
control to change to the correct mode for the
product you want to control. Refer to the table
below. Only one of each device type can be con-
trolled in each mode.
product you want to control. Refer to the table
below. Only one of each device type can be con-
trolled in each mode.
Mode
Affected Device
CAB/SAT
Cable Box
DTV Receiver
Satellite Receiver
DTV Receiver
Satellite Receiver
VCR
VCR
DVR
DVD Player/Recorder
DVD Player/Recorder
DVD
DVD Player/Recorder
DVR
DVR
VCR
AUDIO
A/V Receiver
Audio Amplifier
Audio Amplifier
CD Player
Press and hold
2.
POWER on the remote control for
several seconds until the key flashes twice and
goes off.
Release the
goes off.
Release the
3.
POWER key.
Enter the first five-digit code listed for your equip-
4.
ment in the reference tables that follow.
If you need to start over or wish to exit
programming mode, temporarily change to a
If you need to start over or wish to exit
programming mode, temporarily change to a
different device mode.
Point the remote control at the equipment and
Point the remote control at the equipment and
5.
press
POWER. If the product has no power on/off
function, press a different key, such as
(PLAY),
(STOP), VOLUME UP, or MUTE.
If the equipment responds, the remote control
•
is properly programmed.
If the equipment does not respond, repeat
If the equipment does not respond, repeat
•
steps 4 and 5 with the next five-digit code
listed for your equipment.
listed for your equipment.
Once you have found the correct code, write it in
6.
the space below for future reference.
Mode
Device Type
Code
CABLE/SAT
VCR
DVD
AUDIO
IMPORTANT
You may need to reprogram the remote control after
changing the batteries. Record the codes for each
mode in the space provided to make this faster.
Code Verification
To determine the code programmed for any mode:
Set the mode to the one you wish to verify.
1.
Press and hold
2.
POWER on the remote control for
several seconds until the key flashes twice and goes
off.
Press keys
off.
Press keys
3.
9 9 0
Press
4.
1 and count the flashes of the power key.
Write down the number of flashes as the first digit
of the code.
Repeat step 4 for the other digits of the code.
of the code.
Repeat step 4 for the other digits of the code.
5.
Press
2 to see flashes for the second digit, press 3
for the third digit,
4 for the fourth digit, and 5 for the
fifth digit.
Audio Lock: Universal A/V Receiver
Control
Control
With Audio Lock enabled, the remote control oper-
ates volume and mute on an A/V receiver in all control
modes. Activate Audio Lock if you always use an A/V
receiver with your TV and other A/V equipment.
ates volume and mute on an A/V receiver in all control
modes. Activate Audio Lock if you always use an A/V
receiver with your TV and other A/V equipment.
Program
1.
AUDIO mode for your A/V receiver as
2.
AUDIO mode, hold POWER
on the remote control for several seconds until the
key flashes twice and goes off.
Press keys
key flashes twice and goes off.
Press keys
3.
9 9 3 ENTER
The
POWER key will flash twice to indicate Audio
Lock is active.
To Reset the Remote Control to Operate Volume
and Mute for the TV Speakers
and Mute for the TV Speakers
Press and hold
1.
POWER for several seconds until it
flashes twice and goes off.
Press keys
Press keys
2.
9 9 3 VOLUME UP.
The
POWER key will flash four times to indicate Audio
Lock has cleared.
Appendix A: Programming the Remote Control, continued