Euro-Pro EP035H3 用户手册

Always unplug from 

electrical outlet before opening the dust 

cup (container).

: HEPA dust cup filter must be 

used when operating the hand vacuum.

1. Hold the hand vacuum firmly in 

your hand by the Handle. 

2. Push the On/Off Power Switch to 

“On” position.

3. Start vacuuming.

The Hand Vacuum is 

a very powerful unit.  Make sure 

that you hold it firmly, otherwise it 

can slip out of your hand and 

cause injury.

4. To use the flexible hose, push 

the end of the hose into the 
suction hole, then attach the 
desired brush to the other end 
of the flexible hose, as shown 
below.

When the Intelli-Sense 

Filter Monitor

TM

lights up, it means 

that the dust cup is full or filter 

needs cleaning.  You must empty 

the dust from the dust cup and 

clean the HEPA dust cup filter right 

away. (See illustration below.)

5. Ensure that the turbine wheel moves 

freely by rotating it with your finger. If 

the turbine does not rotate, call 

Customer Service for help.

6. Close and lock the hinged cover on the 

turbo brush and continue vacuuming.

The efficiency of your air driven turbo 

brush depends on the bristle brush 

rotating at high speed. Strong air suction 

is needed to accomplish this. In order to 

ensure that maximum air suction is 

maintained, please read the following 

instructions:
1. Empty the dust cup frequently.

2. Always "TAPCLEAN" the HEPA dust 

cup filter when emptying the dust cup 

container.

3. Ensure that the rotating brush is kept 

free of hair and string which may 

accumulate and decrease brush 

performance.

4. Keep Air Driven Turbo Brush turbine 

free of dirt and foreign matter. (See 

illustration below for cleaning 

instructions.)

1. To open the dust 

cup (container), 

push button and 

pull out the dust 

cup. Verify that the 

HEPA dust cup 

filter is inside, then attach the 

dust cup (container) to the 

hand vacuum.

Always unplug the unit from 

electrical outlet before opening the Dust 

Cup (container).

Do NOT use the HEPA filter 

cartridge without the debris screen in 

place.

After each Use - Always 

remove the Filter Debris Screen from the 

HEPA  Dust Cup Filter, then vigorously 

“TapClean” HEPA Filter until no more 

dust can be removed.

Fig. 1

IMPORTANT, Please Note : The 

“TapClean” HEPA Dust Cup Filter & 

Debris Screen will stop most of the tiniest 

dust particles from re-entering the air you 

breathe. In fact it stops 99.97% of all 

particles as small as 0.3 microns - many 

times smaller than a human hair!!! 

Because of this incredible filtration 

performance, the HEPA Dust Cup Filter 

will quickly accumulate, inside the white 

filter folds, many fine dust particles that 

are difficult to see but which will eventually 

block or reduce your suction power - if not 

cleaned properly. Clean the HEPA Filter 

and Debris Screen after each use as 

described in this section.

2. To use the Hand Vacuum with the 

shoulder strap, attach it to the unit as 

shown below.

3. To attach the oval brush, air driven 

turbo brush or the pet hair removal 

attachment to the Hand Vacuum, 

push attachment into the suction 

hole, as shown below.

From time to time, the turbine of your 

turbo brush will require cleaning. To do 

this:

1. Remove the turbo brush from the hose 

or unit.

2. Turn turbo brush over and open the 

hinged cover to access the turbine 

wheel. (see fig. 1)

3. There may be some dust, lint, hair, etc 

on the turbine wheel. Remove as much 

of this as possible.

4. You may also use the unit’s hose to 

remove any additional debris from the 

turbine.

1. To open the Dust Cup (container), 

push button and detach the Dust 

Cup (container ). (Fig. 2)

2. Pull out the HEPA Dust Cup Filter. 

(Fig. 3)

Fig.3

Fig. 2

The pet hair removal 

attachment is for use on 

upholstery, drapes and other fabric 

surfaces to remove lint, pet hair, 

etc. THE PET HAIR REMOVAL 

4

5