Panasonic WJ-HD716K 用户手册
153
Specifications
• General
Power source:
120 V AC, 60 Hz
Power consumption:
130 W
Ambient operating temperature:
+5 °C to +45 °C {+41 °F to +113 °F}
Ambient operating humidity:
5 % to 90 % (non condensing)
When installing WJ-HDB611: 10 % to 80 % (non condensing)
Maximum operating altitude:
2 000 m {6 562 feet} or less
Dimensions (excluding rubber
feet and projections)
feet and projections)
430 mm (W) x 132 mm (H) x 400 mm (D) {16-15/16"" (W) x 5-3/16" (H) x 15-3/4" (D)}
Weight:
When no hard disk drive is installed: 14 kg {30.91 lbs.}
When 4 hard disk drives are installed: 17 kg {37.53 lbs.}
Finish:
Front cover: Solid metallic coating
Top cover: Solid metallic coating
Rear panel: Galvanized steel
• HDD (Locally procured - Contact your dealer about purchasing hard disk drives.)
Hard disk drive:
3.5" hard disk drive (Up to 4 hard disk drives can be installed.)
• Input/output
Video
Video input connector:
1 V [p-p]/75 Ω, x16 (1ch to 16ch) (BNC)
Vertical timing pulse multiplexed, HD616K: x8 (1ch to 8ch), HD716K: x16
Cascade input connector:
1 V [p-p]/75 Ω (BNC)
HDMI, x2
Video output connector:
1 V [p-p]/75 Ω, active loop-thru output, x16 (1ch to 16ch) (BNC)*
1
Monitor output connector:
1 V [p-p]/75 Ω, x2 (BNC)
Monitor (HDMI) connector:
HDMI, x2*
8
Video output connector (front):
1 V [p-p]/75 Ω, x1 (RCA pin)
Audio
Audio input connector:
–10 dBv, 10 kΩ, unbalanced, x4 (RCA pin)
Cascade input connector:
–10 dBv, 10 kΩ, unbalanced x 1 (RCA pin)
Audio output connector:
–10 dBv, 600 Ω, unbalanced, x1 (RCA pin)
Audio output connector (front):
–10 dBv, 600 Ω, unbalanced, x1 (RCA pin)
Others
External storage connector:
x3
Mouse connection port:
x1
Alarm/control terminal:
8 to 16ch alarm output*
3
, alarm reset input*
2
, emergency recording input*
2
, available
space warning output*
3
, HDD trouble output*
3
, camera trouble output*
3
, trouble out-
put*
3
, electricity failure recovery completion output*
4
, time adjust input/output*
5
,
sequence switching input/output*
5
, alarm suspension input*
2
, electricity failure detec-
tion input*
2
, external recording mode switching*
2
, +5 V output*
6
(25-pin D-sub)
Alarm terminal:
1ch - 16ch alarm input*
2
, 1 - 7ch alarm output*
3
(25-pin D-sub)
RS485 port:
RS485 (full duplex/half duplex*
7
), x2 (RJ-11)
DATA port:
RS485, x2 (RJ-11)
Network port:
10BASE-T/100BASE-TX (RJ-45)
Maintenance port:
10BASE-T (RJ-45)
SDHC/SD memory card slot:
SDHC/SD memory cards applicable (miniSD cards and microSD cards not applica-
ble)
ble)
*1 When power is not supplied, the video output signal was not sent from the recorder even if a video input signal is supplied.
*2 Non-voltage make contact input, 50 kΩ +5 V DC pull-up
*2 Non-voltage make contact input, 50 kΩ +5 V DC pull-up