Moen MT302E 用户手册
TWO HANDLE
TUB & SHOWER VALVE
INSTALLATION INSTRUCTIONS
THESE INSTRUCTIONS MUST BE
LEFT WITH HOMEOWNER
MT302E
MODEL 72964 Series
These are shown on the drawings. The
depth measurment is critical. The center
line of the supply and discharge piping
should be a maximum of 3-1/16” (78mm)
and a minimum of 2” (51mm) behind the
finished wall surface, including tile. This is
1-1/16” (27mm) of adjustment.
depth measurment is critical. The center
line of the supply and discharge piping
should be a maximum of 3-1/16” (78mm)
and a minimum of 2” (51mm) behind the
finished wall surface, including tile. This is
1-1/16” (27mm) of adjustment.
Pipe, ells and nipples are not furnished
with the valve.
with the valve.
Always turn water off before disassembling the valve. Open both valve handles to
relieve water pressure and to insure that COMPLETE water shut-off has been accomplished.
relieve water pressure and to insure that COMPLETE water shut-off has been accomplished.
Before turning water on during either rough-in or trim-out, make sure that cartridge retainer nuts are in place. The cartridges and
retainer nuts were probably installed and tested before leaving the factory. Although it is unlikely, it is nevertheless possible that
through the handling of the valve by any number of persons the retainer nuts may not be properly installed. This should be care-
fully checked at time of rough-in and trim-out. If the retainer nuts are not properly installed, water pressure could force the
cartridges out of the casting. Personal injury or water damage to the premises could result.
retainer nuts were probably installed and tested before leaving the factory. Although it is unlikely, it is nevertheless possible that
through the handling of the valve by any number of persons the retainer nuts may not be properly installed. This should be care-
fully checked at time of rough-in and trim-out. If the retainer nuts are not properly installed, water pressure could force the
cartridges out of the casting. Personal injury or water damage to the premises could result.
Measurements
All that is necessary to clean these faucets is to wipe them with a soft damp cloth such as terrycloth. Warm
water will remove dry water spots. CAUTION: do NOT use cleansers which contain abrasives or harsh
chemicals. NEVER use alcohol or other organic solvents. A high quality, non abrasive wax polish applied
occasionally, will help preserve the deep tones of the finish.
water will remove dry water spots. CAUTION: do NOT use cleansers which contain abrasives or harsh
chemicals. NEVER use alcohol or other organic solvents. A high quality, non abrasive wax polish applied
occasionally, will help preserve the deep tones of the finish.
Cleaning and Care Instructions
for Special Finish Models
CAUTION:
©2007 Moen Incorporated • 25300 Al Moen Drive • North Olmsted, OH 44070-8022 U.S.A.
In Canada Moen Inc. • 2816 Bristol Circle • Oakville, Ontario L6H 5S7
©2007 Moen Incorporated
MT302E - 4/07
Printed in U.S.A.
HELP LINE
Please do not return this product to the store.
If you need installation assistance, replacement parts or have questions regarding our warranty,
please call our Product Consultants at:
U.S.: 1-800-289-6636
Monday - Friday 8:00 a.m. to 8:00 p.m. EST
Saturday 8:00 a.m. to 6:30 p.m. EST
Or e-mail us at: moenwebmail@moen.com
Be sure to visit our website at www.moen.com
Canada 1-800-465-6130
Monday - Friday 7:30 a.m. to 5:00 p.m. EST
Or e-mail us at: cantsd@moen.com
Be sure to visit our website at www.moen.com
When ordering parts, specify finishes.
STOP
SPOUT