AMX HDMI-UTPRO-0808 用户手册
Overview and General Specifications
22
Instruction Manual – HDMI-UTPRO-0808
HDMI-UTPRO-RX Specifications
* We recommend using a regulated power supply for the HDMI-UTPRO-RX. If you exceed the specified voltage level for
the power jack on the RX, the warranty will be void.
the power jack on the RX, the warranty will be void.
AMX reserves the right to modify its products and their specifications without notice.
Common Applications
Whether your displays are across the room, on the other side of the house, or in a classroom down the hall, your sources
can be distributed to up to 8 different displays located remotely. In addition, since UTPRO signals are carried over
commonly available Unshielded Twisted Pair (UTP) cable, the HDMI-UTPRO-0808 is also an extremely cost effective
solution to install.
can be distributed to up to 8 different displays located remotely. In addition, since UTPRO signals are carried over
commonly available Unshielded Twisted Pair (UTP) cable, the HDMI-UTPRO-0808 is also an extremely cost effective
solution to install.
Configuration Information and Control Options
Routing Configuration Information
The HDMI UTPro systems specify two identical virtual matrices for switching signals: VM 0 = All and VM 1 = Video.
These two VMs function the same for this product. Additional VMs can be created with XNConnect configuration
software as one way to deal with sources with limited sink support (see page 65 and page 119).
These two VMs function the same for this product. Additional VMs can be created with XNConnect configuration
software as one way to deal with sources with limited sink support (see page 65 and page 119).
Configuration Options
The WebConsole can be used to configure the master connection for the HDMI UTPro, as well as networking
and time settings. Refer to the “HDMI UTPro WebConsole” chapter on page 69 for details.
Use NetLinx SEND_COMMANDs to configure and control the HDMI UTPro. Refer to the “HDMI UTPro
NetLinx Programming” chapter on page 83 for programming details.
NetLinx Programming” chapter on page 83 for programming details.
HDMI-UTPRO-RX Specifications
Parameter
Value
Approvals
UL, cUL, CE, FCC Class A, RoHS, WEEE
AC Power
100 VAC to 240 VAC, single phase (50 Hz to 60 Hz)
DC Power
12 V to 24 V (+/-10%, desktop power supply included*)
Power Consumption
12 Watts, fully loaded
Thermal Dissipation
41 BTU/hr, fully loaded
Operational Temperature
32° F to 113° F (0° C to 45° C)
Humidity
0 to 90% non-condensing
MTBF
203,000 hours (combined set of 8 RX modules)
Serial Port
Bi-directional RS-232
Baud rates 115200, 57600, 38400, 19200, 9600, 4800, 2400, 1200 (default 9600)
RJ-12 connector
Baud rates 115200, 57600, 38400, 19200, 9600, 4800, 2400, 1200 (default 9600)
RJ-12 connector
IR Control (Optional)
IR Rx Jack: 3.5 mm input port for connection of an IR03 Receiver module (see page 15).
“MIO” protocol is loaded as the default.
IR Tx Jack: 3.5 mm output port for connection of an IR01 Emitter module (see page 15).
The *.IRL file must be loaded for the destination device (see page 98).
For information on compatible IR remote controls, see page 16 and page 18.
“MIO” protocol is loaded as the default.
IR Tx Jack: 3.5 mm output port for connection of an IR01 Emitter module (see page 15).
The *.IRL file must be loaded for the destination device (see page 98).
For information on compatible IR remote controls, see page 16 and page 18.
HDMI Output Connector
HDMI connector connects via HDMI cable to destination device
RJ-45 Input Connector
RJ-45 connector connects via UTP cable to RJ-45 output connector on the
HDMI-UTPRO-0808 enclosure
HDMI-UTPRO-0808 enclosure
Dimensions
3.8 in. (9.69 cm) depth
6 in. (15.24 cm) width
1 in. (2.54 cm) height
6 in. (15.24 cm) width
1 in. (2.54 cm) height
Weight per Module
Approximately 1.5 lbs (0.68 kg) (for shipping weight, see enclosure specifications)