JVC RX-D412B 用户手册
Operating procedure
On the front panel ONLY:
Before you start, remember...
There is a time limit in doing the following steps. If the setting
is canceled before you finish, start from step
There is a time limit in doing the following steps. If the setting
is canceled before you finish, start from step
1
again.
Ex.: When setting the DIGITAL IN 1 terminal
1
Press SETTING.
MULTI JOG now works for the setting operation.
2
Turn MULTI JOG until the item you want
to set appears on the display.
• As you turn MULTI JOG, the setting items change as
follows:
3
Press SET.
The current setting of the selected item appears.
4
Turn MULTI JOG to select the appropriate
setting.
5
Press SET.
Your setting is stored.
6
Repeat steps
2
to
5
to set other items if
necessary.
7
Press SETTING.
The source indication resumes on the display.
1, 7
3, 5
2, 4
SUBWOOFER
Ô FRONT SPK Ô CENTER SPK Ô
SURROUND SPK
Ô S BACK SPK Ô S BACK OUT Ô
DIST UNIT
Ô FRONT L DIST Ô FRONT R DIST Ô
CENTER DIST
Ô SURR L DIST Ô SURR R DIST Ô
S BACK DIST
Ô S BACK L DIST Ô S BACK R DIST Ô
EX/ES/PLIIx
Ô DUAL MONO Ô SUBWOOFER OUT
Ô CROSSOVER Ô LFE ATT Ô MIDNIGHT MODE Ô
DIGITAL IN 1
DIGITAL IN 1
Ô DIGITAL IN 2 Ô DIGITAL IN 3 Ô
AUDIO DELAY
Ô HDMI SELECT Ô CMPNT SELECT
Ô VIDEO OUTPUT Ô (Back to the beginning)
Setting the speakers
To obtain the best possible surround effect from the Surround
and DSP modes, register the setting about the speaker after all
connections are completed.
• If you have performed Precise Surround Setup on pages 16
and DSP modes, register the setting about the speaker after all
connections are completed.
• If you have performed Precise Surround Setup on pages 16
to 18, the following settings are not required.
7 Setting subwoofer information—
SUBWOOFER
Select if you have connected a subwoofer or not.
SUBWFR YES
Select when you have connected a
subwoofer.
The subwoofer indicator (
subwoofer.
The subwoofer indicator (
) lights up on
the display. You can adjust the subwoofer
output level (see page 36).
output level (see page 36).
SUBWFR NO
Select when you have not connected a
subwoofer. Selecting this changes the front
speaker size to “LRG” (see below).
subwoofer. Selecting this changes the front
speaker size to “LRG” (see below).
Initial setting:
NO
7 Setting the speaker size—FRONT SPK (front
speakers), CENTER SPK (center speaker),
SURROUND SPK (surround speakers), S BACK
SPK (surround back speakers)
SURROUND SPK (surround speakers), S BACK
SPK (surround back speakers)
Register the sizes of all the connected speakers.
LRG (large)
Select when the cone speaker size is larger
than 12 cm (4
than 12 cm (4
3
/4 inches).
SML (small)
Select when the cone speaker size is smaller
than 12 cm (4
than 12 cm (4
3
/4 inches).
NO
Select when you have not connected
the speaker. (Not selectable for the front
speakers.)
the speaker. (Not selectable for the front
speakers.)
Initial setting:
LRG (for the front speakers)
SML (for the other speakers)
SML (for the other speakers)
NOTES
• If you have selected “SML (small)” for the front speaker size, you
cannot select “LRG (large)” for other speakers.
• When “SUBWOOFER” is set to “NO,” the front speaker size is fixed to
“LRG (large)” (and you cannot select “SML (small)”).
• When “SURROUND SPK” is set to “SML (small),” you cannot select
“LRG (large)” for the surround back speaker.
• When “SURROUND SPK” is set to “NO,” the surround back speaker is
fixed to “NO.”
DVR/DVD
Ô DBS Ô VCR Ô TV
30
29-34_BasicSt.indd 30
29-34_BasicSt.indd 30
06.5.19 1:14:26 PM
06.5.19 1:14:26 PM