ONKYO HT-R640 用户手册
42
First Time Setup
—Continued
With these settings, you can specify which speakers are
connected and a crossover frequency for each speaker.
connected and a crossover frequency for each speaker.
The following crossover frequencies can be specified:
Full Band, 40 Hz, 50 Hz, 60 Hz, 80 Hz, 100 Hz, 120 Hz,
150 Hz, 200 Hz.
Specify Full Band for speakers that can output low-fre-
quency bass sounds adequately, for example, speakers
with a good sized woofer. For smaller speakers, specify
a crossover frequency. Sounds below the crossover fre-
quency will be output by the subwoofer instead of the
speaker. Refer to your speakers’ manuals to determine
the optimum crossover frequencies.
Full Band, 40 Hz, 50 Hz, 60 Hz, 80 Hz, 100 Hz, 120 Hz,
150 Hz, 200 Hz.
Specify Full Band for speakers that can output low-fre-
quency bass sounds adequately, for example, speakers
with a good sized woofer. For smaller speakers, specify
a crossover frequency. Sounds below the crossover fre-
quency will be output by the subwoofer instead of the
speaker. Refer to your speakers’ manuals to determine
the optimum crossover frequencies.
Speaker Configuration
1
Press the [RECEIVER] or [AMP]
button followed by the [SETUP]
button.
button followed by the [SETUP]
button.
The main menu appears onscreen.
MUTING
PREVIOUS
MENU
GUIDE
TOP MENU
SETUP
RETURN
PLAYLIST/CAT
PLAYLIST/CAT
--/---
TAPE/AMP
M D/CDR
HDD
CABLE
STANDBY/ON
DIMMER
ENT
D TUN
SLEEP
10
11
12
INPUT SELECTOR
REMOTE MODE
V
1
V
4
V
2
V
3
C D
TAPE
TUNER
DVD
MULTI CH
T V
VOL
VOL
SAT
VCR
T V
DVD
RECEIVER
C D
INPUT
+10
0
CLR
1
2
3
4
5
6
7
8
9
ENTER
CH
DISC
ALBUM
1, 11
2-10
2
1
RECEIVER
AMP
SETUP
2
Use the Up and Down [
]/[
]
buttons to select “1. Speaker
Config,” and then press [ENTER].
Config,” and then press [ENTER].
The Speaker Config menu appears.
3
Use the Up and Down [
]/[
]
buttons to select “a. Subwoofer,”
and then use the Left and Right
[
and then use the Left and Right
[
]/[
] buttons to select:
Yes: Select if a subwoofer is con-
nected.
No: Select if no subwoofer is con-
nected.
4
Use the Up and Down [
]/[
]
buttons to select “b. Front,” and
then use the Left and Right [
then use the Left and Right [
]/
[
] buttons to select a crossover
frequency.
Note:
If the Subwoofer setting in step 3 is set
to No, this setting is fixed at Full Band.
If the Subwoofer setting in step 3 is set
to No, this setting is fixed at Full Band.
5
Use the Up and Down [
]/[
]
buttons to select “c. Center,” and
then use the Left and Right [
then use the Left and Right [
]/
[
] buttons to select a crossover
frequency.
If no center speaker is connected, select
None.
None.
Note:
If the Front setting in step 4 is set to
anything other than Full Band, Full
Band cannot be selected here.
If the Front setting in step 4 is set to
anything other than Full Band, Full
Band cannot be selected here.
1.Speaker Config
------------------------
a.Subwoofer :Yes
b.Front : 100Hz
c.Center : 100Hz
d.Surround : 100Hz
e.LPFofLFE : 120Hz
f.DoubleBass :---
------------------------
a.Subwoofer :Yes
b.Front : 100Hz
c.Center : 100Hz
d.Surround : 100Hz
e.LPFofLFE : 120Hz
f.DoubleBass :---