Pioneer VSX-1325-K 用户手册

En

If no operations are performed for 10 seconds while the 
speaker configuration check screen is being displayed, 
the Auto MCACC Setup will resume automatically. In this 
case, you don’t need to select ‘OK’ and press ENTER in 
step 8.

• If you see an ERR message (or the speaker 

configuration displayed isn’t correct), there may be a 
problem with the speaker connection.
If selecting RETRY doesn’t work, turn off the power 
and check the speaker connections. If there doesn’t 
seem to be a problem, you can simply use 

/ to 

select the speaker and 

/ to change the setting 

and continue. 

• If Reverse Phase is displayed, the speaker’s wiring 

(+ and –) may be inverted. Check the speaker 
connections.

1

– If the connections were wrong, turn off the power, 
disconnect the power cord, then reconnect properly. 
After this, perform the Full Auto MCACC procedure 
again.
– If the connections were right, select GO NEXT and 
continue.

A progress report is displayed on-screen while the 
receiver outputs more test tones to determine the 
optimum receiver settings.

Again, try to be as quiet as possible while this is 
happening. It may take 3 to 7 minutes.

• If you selected a STAND.WAVE Multi-Point setup 

(in step 2), you will be asked to place the mic at the 
2nd and 3rd reference points before finally placing it 
at your main listening position.

the Advanced MCACC menu reappears automatically.
The settings made in the Auto MCACC Setup should give 
you excellent surround sound from your system, but it is 
also possible to adjust these settings manually using the 
Manual MCACC setup menu (starting below) or Manual 
SP Setup menu (starting on page 82).

2

You can also choose to view the settings by selecting 
individual parameters from the MCACC Data Check 
screen (see Checking MCACC Data on page 79).

Press RETURN after you have finished checking each 
screen. When you’re finished, select RETURN to go back 
to the Home Menu.

Be sure to disconnect the microphone from this receiver 
upon completion of the Auto MCACC Setup.

You can use the settings in the Manual MCACC setup 
menu to make detailed adjustments when you’re more 
familiar with the system. Before making these settings, 
you should have already completed Automatically 
conducting optimum sound tuning (Auto MCACC) on 
page 37.

You only need to make these settings once (unless you 
change the placement of your current speaker system or 
add new speakers).

• The test tones used in the Manual MCACC setup are 

output at high volume.

• Press the MCACC button while the pertinent setup 

screens are displayed to select MCACC presets.

• For some of the settings below, you’ll have to connect 

the setup microphone to the front panel and place it 
about ear level at your normal listening position. 
Press HOME MENU to display the Home Menu 
before you connect the microphone to this receiver.

• See Problems when using the Auto MCACC Setup on 

page 39 for notes regarding high background noise 
levels and other possible interference.

• If  you’re using a subwoofer, switch it on and turn up 

the volume to the middle position.

MCACC menu. 
See Making receiver settings from the Advanced MCACC 
menu on page 73 if you’re not already at this screen. 

If you’re doing this for the first time, you might want to 
make these settings in order.

• Fine Channel Level – Make fine adjustments to the 

overall balance of your speaker system (see Fine 
Channel Level on page 76).

• Fine SP Distance – Make precise delay settings for 

your speaker system (see Fine Speaker Distance on 
page 76).

1 If  the  speaker is not pointed to the microphone (listening position) or when using speakers that affect the phase (dipole speakers, reflective 

speakers, etc.), Reverse Phase may be displayed even if the speakers are properly connected.

2 •  Depending on the characteristics of your room, sometimes identical speakers with cone sizes of around 12 cm (5 inches) will end up with 

different size settings. You can correct the setting manually using the Manual speaker setup on page 82.
• The subwoofer distance setting may be farther than the actual distance from the listening position. This setting should be accurate (taking 
delay and room characteristics into account) and generally does not need to be changed.
• If Auto MCACC Setup measurement results are incorrect due to the interaction of the speakers and viewing environment, we recommend 
adjusting the settings manually.

VSX-1325_UXJCB.book  75 ページ  ２０１０年３月９日　火曜日　午後３時４分