Sony STRDG800 用户手册
86
US
F:\Sony SEM
HA\Revision2_DG800\JC060412_2667346121DG800_US\2667346121\US05AMP_STR-DG800-
CEL.fm
HA\Revision2_DG800\JC060412_2667346121DG800_US\2667346121\US05AMP_STR-DG800-
CEL.fm
masterpage: Left
STR-DG800
2-667-346-12 (1)
Programming the remote
You can program the remote to control non-
Sony components by changing the code. Once
the control signals have been memorized, you
can use those components as part of your
system.
Furthermore, you can also program the remote
for Sony components that the remote is unable
to control. Note that the remote can only
control components that accept infrared
wireless control signals.
Sony components by changing the code. Once
the control signals have been memorized, you
can use those components as part of your
system.
Furthermore, you can also program the remote
for Sony components that the remote is unable
to control. Note that the remote can only
control components that accept infrared
wireless control signals.
1
Press RM SET UP.
The RM SET UP indicator slowly flashes.
2
Press the input button
(including TV) for the
component you want to control.
(including TV) for the
component you want to control.
For example, if you are going to control a
CD player, press SA-CD/CD. The RM
SET UP indicator lights up.
CD player, press SA-CD/CD. The RM
SET UP indicator lights up.
3
Press the numeric buttons to
enter the numeric code (or one
of the codes if more than one
code exists) corresponding to
the component and the maker
of the component you want to
control.
enter the numeric code (or one
of the codes if more than one
code exists) corresponding to
the component and the maker
of the component you want to
control.
See the tables on pages 87–90 for
information on the numeric code(s)
corresponding to the component and the
maker of the component (the first digit
and the last two digits of the numeric code
correspond to the category and the
maker’s code respectively.)
information on the numeric code(s)
corresponding to the component and the
maker of the component (the first digit
and the last two digits of the numeric code
correspond to the category and the
maker’s code respectively.)
4
Press ENTER.
Once the numeric code has been verified,
the indicator slowly flashes twice and the
remote automatically exits the
programming mode.
the indicator slowly flashes twice and the
remote automatically exits the
programming mode.
5
Repeat steps 1 to 4 to control
other components.
other components.
To cancel programming
Press RM SET UP during any step. The
remote automatically exits the programming
mode.
remote automatically exits the programming
mode.
To activate the input after
programming
programming
Press the programmed button to activate the
input you want.
input you want.
If programming is
unsuccessful, check the
following:
unsuccessful, check the
following:
• If the indicator does not light up in step 1, the
batteries are weak. Replace both batteries.
• If the indicator flashes 4 times in quick
succession while entering the numeric code,
an error has occurred. Start again from step
1.
an error has occurred. Start again from step
1.
Notes
• The indicator turns off while a valid button is
pressed.
• In step 2, if several input buttons are pressed, only
the last pressed button is valid.
• In step 3, if an input button is pressed, the new
input is selected and the programming procedure
returns to the beginning of step 3.
returns to the beginning of step 3.
• For the numeric codes, only the last three numbers
entered are valid.
• In step 2, if you press TV, you can only program the
button to control a TV (page 89).
If you press TUNER, you can only program the
button to control a tuner (page 90).
button to control a tuner (page 90).
To clear the memory of the remote
To clear all programmed and learned signals,
do the following to reset the remote to factory
settings.
do the following to reset the remote to factory
settings.
Press ?/1, AV ?/1 and MASTER
VOL – at the same time.
VOL – at the same time.
The indicator flashes 3 times, then goes off.
Using the Remote
US01COV_STR-DG800-CEL.book Page 86 Tuesday, March 14, 2006 3:53 PM