Linn Twin Klimax 用户手册

Single ended

7K8ohms

Balanced

7K8ohms

Balanced

2v rms 

Unalanced

4v rms 

Single ended

1.67 Vrms

Signal sensing threshold

>150uV

Standard

Neutrik

Optional

Binding posts

230W rms into 4ohms

100W rms into 8ohms

Unconditionally stable into all loudspeaker loads

>0.02%

7Hz to 35kHZ (-3dB)

46V

• Wall mount system     • Active crossover system    •  Binding post output terminals

1.

Read instructions. Read the safety and operating instructions before operating the appliance.

2.

Retain instructions. Retain the safety and operating instructions for future reference.

3.

Heed warnings. Observe all warnings on the appliance and in the operating instructions.

4.

Follow instructions. Follow all operating and use instructions.

5.

Water and moisture . Do not use the appliance near water, for example near a bathtub, washbowl, kitchen sink, laundry tub, in a 

wet basement, or near a swimming pool and the like.

6.

Carts and stands. Use only with a cart or stand that is recommended by the manufacturer

6a.

An appliance and cart combination should be used with care. Quick stops, excessive force, and uneven surfaces may cause the 

appliance and cart combination to overturn.

7.

Wall or ceiling mounting. Mount to a wall or ceiling only as recommended by the manufacturer.

8.

Ventilation. Site the appliance so that its location or position does not interfere with its proper ventilation. For example, the 

appliance should not be situated on a bed, sofa rug, or similar surface that may block the ventilation openings, or placed in a 

built-in installation such as a bookcase or cabinet that may impede the flow of air though the ventilation openings.

9.

Heat. Site the appliance away from heat sources such as radiators, heaters, stoves, or other appliances (including amplifiers) that 

produce heat.

10.

Power sources. Connect the appliances to a power supply only of the type described in the operating instructions or marked on 

the appliance.

11.

Grounding or polarisation. Do not defeat the safety purpose of the polarised or grounding type plug. A polarised  plug has two 

blades with one wider than the other. A grounding type plugs has two blades and a third grounding prong. The wide blade or the

third prong is provided for your safety. When the provided plug does not fit into your outlet, consult an electrician for 

replacement of the obsolete outlet.

12.

Power card protection. Route power cords so that they are not likely to be walked on or pinched by items placed upon or against 

them, paying particular attention to cords at plugs, power sockets, and at the point where they exit from the appliance.

13.

Protective attachment plug. As a safety feature the product is equipped with an attachment plug containing overload protection.

See the instruction manual about resetting or replacing the plug. Should the plug need replacing, ensure that a replacement is 

used which has the same overload protection as the original.

14.

Cleaning. The product should be cleaned only as recommended by the manufacturer.

15.

Power lines. An outdoor antenna should be located away from power lines.

16.

Outdoor antenna grounding. If an outdoor antenna is connected to the tuner/receiver, ensure that the antenna system is 

grounded to provide some protection against voltage surges and static build up. In the USA see article 810 of the National 

Electrical Code ANSI/NFPA 70 concerning installation requirements.

17.

Unplug this apparatus during lightning storms or when unused for long periods of time.

18.

Objects and liquid entry. Take care not to let objects or liquids fall into the product.

19.

Damage requiring service. The product should be serviced by qualified personnel if:

a)

The power cord or plug has been damaged.

b)

Objects or liquid have fallen into the product.

c)

The product has been exposed to rain.

d)

The product does not appear to operate normally or exhibits a marked change in operation.

e)

The product has been dropped or the enclosure damaged.

20.

Servicing. Don’t attempt to service the product beyond that described in the operating instructions. All other servicing 

should be referred to qualified service personnel.