Nilfisk Alto DPA 4000 用户手册
6. Level Control for Channels 1&2
These two controls are used to adjust output level of channel 1 and channel 2 respectively.
7. UP/DOWN Key
This key is used to move inside the menus or to modify the parameter's value.
8. SELECT Key
This key is used to select the menu that you wish to edit.
9. ENTER Key
This key is used to edit or confirm the parameter's value.
10. Power Source Socket
It is used to connect power cord after setting the proper voltage, connect one end of power cord with the unit
and another end with mains.
and another end with mains.
11. Breaker
This switch functions as fuse for protecting the unit from damage. When the unit is overloaded or the
temperature inside the unit is too high, this pushing button will spring up and break the power supply. The
power supply will be recovered after pushing this switch down again.
temperature inside the unit is too high, this pushing button will spring up and break the power supply. The
power supply will be recovered after pushing this switch down again.
12. Output Connector
These connectors have two kinds: Binding post and Speak-on connector. You can choose proper connectors
according to practical need. For your safety, please be careful when do connecting work.
according to practical need. For your safety, please be careful when do connecting work.
13. Limiter Switch
Set this switch at "ON" position, once the output level is above maximum output level, the limiter begins,
thus keeping consistent output level for protecting apparatus. If the switch is set at "OFF", the limiter function
doesn't work.
thus keeping consistent output level for protecting apparatus. If the switch is set at "OFF", the limiter function
doesn't work.
3.2 Rear Panel
These connectors connect the input signal of channel 1 and channel 2 separately.
14. Balanced Input Connectors
These two output connectors are paralleled inside with the two input connectors. It enables the unit to work under
paralleled mode. Please also refer to wiring diagram for paralleled mode.
paralleled mode. Please also refer to wiring diagram for paralleled mode.
15. Parallel Output Connectors
16. Mode Selector
Total two optional modes: Up for Stereo mode; Down for Bridge mode.
- Stereo Mode
In this mode, channel 1 and channel 2 operate independently (just as traditional stereo amplifier). The signal
input into channel 1 can be output from channel 1 only, similarly, the signal input into channel 2 can be output
from channel 2 only.You can also operate the paralleled mode via outside wiring, so, the signal input from
channel 1 or 2 will be output from both channel 1 and 2 simultaneously. Details refer to the chapter 9.
input into channel 1 can be output from channel 1 only, similarly, the signal input into channel 2 can be output
from channel 2 only.You can also operate the paralleled mode via outside wiring, so, the signal input from
channel 1 or 2 will be output from both channel 1 and 2 simultaneously. Details refer to the chapter 9.
- Bridge Mode
In this mode, the signal input into channel 1 will be output from the bridged end, on the other hand, the
output level control of channel 2 should be turned down to smallest.Details refer to the chapter 9.
output level control of channel 2 should be turned down to smallest.Details refer to the chapter 9.
5
Apparaten skall anslutas
till jordat uttag nar den
ansluts till ett natverk
till jordat uttag nar den
ansluts till ett natverk
CH1
BALANCED
INPUT
PARALLEL
OUTPUT
LIMITER
OFF
ON
CH2
BALANCED
INPUT
PARALLEL
OUTPUT
MODE
BRIDGE
STEREO
CH1
OUTPUT1
OUTPUT2
POWER OUTPUTS
CH1
1+
1-
POS
NEG
CH2
BRIDGE
MONO
CH2
2+
2-
POS
NEG
BRIDGE
1+
2+
POS
NEG
CH2
1+
1-
POS
NEG
BREAKER
INPUT
INPUT
TIP/PIN 2
RING/PIN 3
SLEEVE/PIN 1
RING/PIN 3
SLEEVE/PIN 1
TIP/PIN 2
RING/PIN 3
SLEEVE/PIN 1
RING/PIN 3
SLEEVE/PIN 1
INPUT
INPUT
2
1
2
1
3
11
14
10
17
16
12
13
15
15
2
1
2
1
3
20
19
18
RS485 IN
RS485 OUT
RS232
SERIAL PORT