DLS Svenska AB A1 用户手册
Tools and material needed
Tools:
Flat and Phillips screwdrivers
Wire cutter
Wire stripper
Electric drill with drills
Crimping tool
Digital multimeter or test lamp
Wire brush, scraper or a piece
of an abrasive sheet to remove
paint for a good ground connection
Grease to protect the ground
connection from oxidation
Wire cutter
Wire stripper
Electric drill with drills
Crimping tool
Digital multimeter or test lamp
Wire brush, scraper or a piece
of an abrasive sheet to remove
paint for a good ground connection
Grease to protect the ground
connection from oxidation
Material:
Speaker wire: minimum
12 AWG = 4 mm
12 AWG = 4 mm
2
for subwoofers
13 – 16 AWG = 1,5-2,5 mm
2
for other
speakers
Sheet metal screws for mounting the
amplifier to the amplifier board and the
amplifier board to the car + some extra
for fuse holder, amplifier ground etc.
amplifier to the amplifier board and the
amplifier board to the car + some extra
for fuse holder, amplifier ground etc.
Electrical insulation tape
½ inch thick plywood or particle board for
the amplifier to be mounted upon.
the amplifier to be mounted upon.
Amplifier installation kit:
If available,buy an amplifier installation kit. It
contains normally all you need. This is what you
have to buy if you buy the items separately
If available,buy an amplifier installation kit. It
contains normally all you need. This is what you
have to buy if you buy the items separately
20- 25 feet = 6- 7.5 meter power cable,
preferably AWG 5 = 16 mm
preferably AWG 5 = 16 mm
2
or heavier. See
the table on previous page to find out what
cable size you need.
cable size you need.
1 pc of fuseholder to install close to the
car battery + fuse 80 Ampere, or other value
depending on what cable and amplifier you
use. See the table on page 2.
car battery + fuse 80 Ampere, or other value
depending on what cable and amplifier you
use. See the table on page 2.
20 feet of AWG 15 = 1,5 mm
2
wire for
remote turn on / off cable from head unit.
RCA-cable for input from head unit.
- 20 feet or 5 meter for trunk installations
You can connect all inputs together and use
only one RCA-cable, or use separate wires
to each input.
- 20 feet or 5 meter for trunk installations
You can connect all inputs together and use
only one RCA-cable, or use separate wires
to each input.
Two min. 5 gauge ring crimp terminals –one
for connection to the battery plus and one
for the amplifier ground connection.
for connection to the battery plus and one
for the amplifier ground connection.
Wire ties
Insulating grommet or insulating tube
Routing wires
Stereo
head unit
3
ULTIMATE A-series
Professional Tip:
Gauge (ga) is an American measure for cable size,
also called AWG (American Wire Gauge).
also called AWG (American Wire Gauge).
CONVERSION GAUGE - mm
2
0 AWG = 50 mm
2
1 AWG = 42 mm
2
9 AWG = 6,8 mm
2
2 AWG = 33 mm
2
10 AWG = 5,3 mm
2
3 AWG = 27 mm
2
11 AWG = 4,2 mm
2
4 AWG = 21 mm
2
12 AWG = 3 mm
2
5 AWG = 16 mm
2
13 AWG = 2,7 mm
2
6 AWG = 13 mm
2
14 AWG = 2 mm
2
7 AWG = 10 mm
2
15 AWG = 1,65 mm
2
8 AWG = 8 mm
2
16 AWG = 1,3 mm
2