JL Audio SB-T-TUNDCMAX/13TW5/DG 用户手册
SB-T-TDCMAX/13TW5 INSTR_SKU# 011266
Page 4 • JL Audio, Inc 2008
S T E P 1 9
We suggest wiring the enclosure at this point, it will be very
hard (or impossible) to access the terminal cup if the second
Stealthbox® is installed. Route the wire using a safe, secure
method to the amplifier location. Always ensure that wires
cannot be pinched or damaged along the path to the next
component.
We suggest wiring the enclosure at this point, it will be very
hard (or impossible) to access the terminal cup if the second
Stealthbox® is installed. Route the wire using a safe, secure
method to the amplifier location. Always ensure that wires
cannot be pinched or damaged along the path to the next
component.
If installing two Stealthboxes®, we suggest wiring the second
enclosure before mounting as the terminals will be much
more accessible than after the enclosure is mounted. Repeat
enclosure before mounting as the terminals will be much
more accessible than after the enclosure is mounted. Repeat
steps 17-19 for the second Stealthbox®.
S T E P 1 8
This is a cross-sectional drawing showing the bolt from step
This is a cross-sectional drawing showing the bolt from step
13 also passing through the interior plastic trim panel and
the Stealthbox®. The bolt then holds the Stealthbox® in place
via the fender washer, split lock washer and, nut. Again, be
cautious not to overtighten the nut, it only needs to be snug.
the Stealthbox®. The bolt then holds the Stealthbox® in place
via the fender washer, split lock washer and, nut. Again, be
cautious not to overtighten the nut, it only needs to be snug.
LOCK WASHER
REMOVEABLE INTERIOR
REAR WALL
REAR WALL
HEX NUT
FENDER WASHER
FRONT OF TRUCK
STEALTHBOX®
INTERIOR PLASTIC TRIM PANEL
COMPLETED IN
STEP 16
STEP 16
S T E P 2 0
Place the bottom edge of the woofer on the enclosure,
attach wires to the appropriate connectors. Lean the woofer
back into location and make sure that wires do not get
pinched either betwen the woofer and the enclosure or the
securing hardware.
Place the bottom edge of the woofer on the enclosure,
attach wires to the appropriate connectors. Lean the woofer
back into location and make sure that wires do not get
pinched either betwen the woofer and the enclosure or the
securing hardware.
S T E P 2 1
Use a sharp pointed object to align the woofer with the
holes previously used to mount it, re-mount the woofer. Use
a “crossing “ pattern as if re-mounting a repaired flat tire. If
installing two Stealthbox ® enclosures, repeat this procedure
in both enclosures. Again, the grilles did not need to be
removed!
Use a sharp pointed object to align the woofer with the
holes previously used to mount it, re-mount the woofer. Use
a “crossing “ pattern as if re-mounting a repaired flat tire. If
installing two Stealthbox ® enclosures, repeat this procedure
in both enclosures. Again, the grilles did not need to be
removed!
C o n G R a t u l a t I o n s !
You have completed the installation for this model!
Enjoy your new Stealthbox®!
Please refer to the Power Recommendation section for an
amplifier recommendation and basic set-up help.
Please refer to the Power Recommendation section for an
amplifier recommendation and basic set-up help.
All specifications are subject to change without notice. “JL Audio®” and the JL Audio logo, “Stealthbox” and the Stealthbox logo are registered
trademarks of JL Audio, Inc. “Ahead of the Curve” and its respective logo is a trademark of JL Audio, Inc.
JLA-SKU# 011266
8-12-2008 • Printed in USA • ©2007 JL Audio, Inc. • U.S. PATENTS: #5,734,734 #5,949,898 #6,118,884 #6,229,902 #6,243,479
#6,294,959 #6,501,844 #6,496,590 #6,441,685 #5,687,247 #6,219,431 #6,625,292 #D472,891 #D480,709 Other U.S. & Foreign patents pending.
(954) 443-1100
w w w. j l a u d i o . c o m
1 0 3 6 9 N O R T H C O M M E R C E P A R K W A Y • M I R A M A R , F L O R I D A • 3 3 0 2 5 • U S A
I n C l u d e d H a R d W a R e P e R s t e a l t H B o X ®
(1) 3/8-16 X 1 1/2" Hex Head Bolt
(3) 3/8 X 1 1/4" Fender Washer
(2) 3/8" Split Lock Washer
(2) 3/8 X 16 Hex Nut
s P e C I F I C a t I o n s
Enclosure Type: Acoustic Suspension (sealed)
Driver Type: 13TW5-3
Nominal Impedance: 3 ohms mono
Continuous Power Handling: 600 Watts
P o W e R R e C o M M e n d a t I o n
JL Audio recommends using a high quality amplifiers such as the JL Audio 500/1v2. The 500/1v2 could be used for
one or, two Stealthboxes. The ideal amplifier for two enclosures is the HD750/1. The diagram below shows the
recommended crossover, infrasonic filter and equalizer settings for the 500/1v2 when being used to power your
Stealthbox
one or, two Stealthboxes. The ideal amplifier for two enclosures is the HD750/1. The diagram below shows the
recommended crossover, infrasonic filter and equalizer settings for the 500/1v2 when being used to power your
Stealthbox
®
.
The JL Audio 500/1v2 and the HD750/1 are very versatile audio components. Please consult the owner’s manual
for even more detailed information about installing and tuning these amplifiers.
for even more detailed information about installing and tuning these amplifiers.
M I d / H I G H F R e q u e n C Y d R I v e R F I t M e n t
A variety of JL Audio coaxial and component systems will fit in the factory speaker locations of your vehicle.
Dash Speaker Size / JL Audio Model: 3.5” - TR350-CXi
Front Speaker Size / Location: 6”x 9” - Front Doors
Fits JL Audio Models: TR690-TXi, VR690-CXi
Rear Speaker Size / Location: 6.5” - Rear Door
Fits JL Audio Models: TR650-CXi, TR650-CSi, VR650-CXi, VR650-CSi,
C5-650, C5-650x, ZR650-CSi
+12VDC
Remote
Ground
JL AUDIO 500/1
five-channel system amplifier
+
_
_
+
Subwoofer Output
MONO OUTPUT ONLY
40
45
55
65
85
120
200
Filter Freq. (Hz)
Mode / Slope
Off / 12dB / 24dB
Amp LP Filter
Infrasonic Freq. (Hz)
15
18
25
30
40
50
60
Off / 30Hz
Infrasonic Filter
0.5
0.7
1.1
1.6
2.7
4.3
"Q"
20
25
35
45
55
70
85
Center Freq.
0
+4
+10
+13
+15
Boost (dB)
Off / On
Bass EQ
Remote Bass Port
Advanced
Bass
Control
Preamp Output Section
Full Range / Amp Filter / Out Filter
Output Mode
Filter Slope
12dB / 24dB
40
45
55
65
85
120
200
Filter Freq. (Hz)
Left Ch.
Right Ch.
Filter Mode
LP / HP
Amplifier Input Section
Input Sens.
Left Ch.
Right Ch.
Signal Sensing
Off / On
Input Voltage
Low / High