ONKYO TX-SR702E 操作指南
78
Zone 2
—Continued
Here you can turn on Zone 2, select an input source, and
adjust the volume.
adjust the volume.
Note:
To control Zone 2 with the remote controller, you must
press the [ZONE 2] button first.
press the [ZONE 2] button first.
Notes:
• If the Sleep function has been set, the Zone 2 compo-
nent will turn off along with the AV receiver when the
specified sleep time expires. To use the Sleep function
with Zone 2 only, set the Sleep function and then set
the AV receiver to Standby.
specified sleep time expires. To use the Sleep function
with Zone 2 only, set the Sleep function and then set
the AV receiver to Standby.
• Only analog input sources are output by the ZONE 2
LINE OUT and ZONE 2 SPEAKERS terminals. Dig-
ital input sources are not output. If no sound is heard
when an input source is selected, check if it’s con-
nected to an analog input.
ital input sources are not output. If no sound is heard
when an input source is selected, check if it’s con-
nected to an analog input.
• Since the Zone 2 function and the REC OUT outputs
use the same circuitry, if the [REC OUT] function is
used, Zone 2 will be turned off.
used, Zone 2 will be turned off.
• While Zone 2 is being used, listening modes that need
surround back speakers (i.e., Dolby Digital EX, DTS-
ES, and THX Surround EX) are unavailable.
ES, and THX Surround EX) are unavailable.
• While Zone 2 is on,
functions will not work.
• You can’t select different radio stations for Zone 2 and
the main room. For example, if you an FM station for
the main room, that station will also be used in Zone 2.
the main room, that station will also be used in Zone 2.
Using Zone 2
1
Point the remote controller at the
AV receiver and press the
[ZONE 2] button followed by the
[ON] button.
AV receiver and press the
[ZONE 2] button followed by the
[ON] button.
This turns on Zone 2 and the AV
receiver’s 12V TRIGGER OUT.
receiver’s 12V TRIGGER OUT.
2
To select the Zone 2 input source
with the remote controller, press
the [ZONE 2] button followed by
an input selector button.
with the remote controller, press
the [ZONE 2] button followed by
an input selector button.
If you select AM or FM, you can use
the remote controller’s [TUNER] but-
ton to select the band.
the remote controller’s [TUNER] but-
ton to select the band.
To perform steps 1 and 2 on the
AV receiver, press the [ZONE 2]
button, and then use the Control-
ler [
AV receiver, press the [ZONE 2]
button, and then use the Control-
ler [
]/[
] buttons within five
seconds.
The name of the selected Zone 2 source
appears on the display.
appears on the display.
3
1–4
4
2
1
ZONE
2
ON
ZONE
2
To set Zone 2 to the same source as the
main room, press the [ZONE 2] button,
and then use the Controller [
main room, press the [ZONE 2] button,
and then use the Controller [
]/[
]
buttons to select “Zone 2 Sel: Source.”
3
To adjust the Zone 2 volume with
the remote controller, press the
[ZONE 2] button, and then use
the [LEVEL–] and [LEVEL+] but-
tons.
the remote controller, press the
[ZONE 2] button, and then use
the [LEVEL–] and [LEVEL+] but-
tons.
To do this on the AV receiver,
press the ZONE 2 [LEVEL] but-
ton, and then use the Controller
[
press the ZONE 2 [LEVEL] but-
ton, and then use the Controller
[
]/[
] buttons.
If the Zone 2 receiver/integrated amp is
connected to the AV receiver’s ZONE 2
LINE OUT L/R jacks, use the volume
control on the receiver/integrated amp.
connected to the AV receiver’s ZONE 2
LINE OUT L/R jacks, use the volume
control on the receiver/integrated amp.
4
To turn off Zone 2 with the
remote controller, press the
[ZONE 2] button followed by the
[STANDBY] button.
remote controller, press the
[ZONE 2] button followed by the
[STANDBY] button.
To do this from the AV receiver,
press the [ZONE 2] button, and
then use the Controller [
press the [ZONE 2] button, and
then use the Controller [
]/[
]
buttons to select OFF.
ZONE
2
LEVEL+
LEVEL-
ZONE
2
STANDBY
TX-NR702,602_En.book Page 78 Tuesday, September 7, 2004 1:18 PM