Panasonic VL-566BX 产品宣传页
1-62, 4-chome, Minoshima, Hakata-ku, Fukuoka 812-8531, Japan
© Panasonic System Networks Co., Ltd. 2010
Door Station
Model No.
VL-V566BX
Installation and Operation Guide
Thank you for purchasing a Panasonic product.
L
Please read this guide before using the unit and save for
future reference.
future reference.
L
Please read this guide carefully, and install the unit safely
and correctly by following the instructions. Panasonic
assumes no responsibility for injuries or property damage
resulting from failures arising out of improper installation or
operation inconsistent with this guide.
and correctly by following the instructions. Panasonic
assumes no responsibility for injuries or property damage
resulting from failures arising out of improper installation or
operation inconsistent with this guide.
For your safety
To prevent severe injury and loss of life/property, read this section carefully
before using the unit to ensure proper and safe operation of your unit.
before using the unit to ensure proper and safe operation of your unit.
WARNING
L
To reduce the risk of electric shock, do not disassemble this unit. Refer
servicing to an authorized service center when service is required. Opening or
removing covers may expose you to dangerous voltages or other risks. Incorrect
reassembly can cause electric shock when the unit is subsequently used.
servicing to an authorized service center when service is required. Opening or
removing covers may expose you to dangerous voltages or other risks. Incorrect
reassembly can cause electric shock when the unit is subsequently used.
L
Never install wiring during a lightning storm.
L
When existing chime wires are used, it is possible that they contain AC voltage.
Electric shock or unit damage could result. Contact an authorized service center.
Electric shock or unit damage could result. Contact an authorized service center.
CAUTION
L
Install the unit securely adhering to the instructions in this guide to prevent
it from falling off the wall. Avoid installing onto low-strength walls, such as
gypsum board, ALC (autoclaved lightweight concrete), concrete block, or
veneer (less than 18 mm thick) walls.
it from falling off the wall. Avoid installing onto low-strength walls, such as
gypsum board, ALC (autoclaved lightweight concrete), concrete block, or
veneer (less than 18 mm thick) walls.
L
If the wiring is underground, do not make any connections underground.
L
If the wiring is underground, use a protection tube.
PNQW2397ZA SV0910MT0
For your future reference
Date of purchase
Serial number (found on the rear of the door station)
Dealer’s name and address
Dealer’s telephone number
Attach your sales receipt here.
Included accessories
L
Wood screws ..................2
(3.8 mm × 20 mm)
L
Attached to the bag the door station
is in.
is in.
Location of controls
A Lens cover
B Camera
C {CALL} button and indicator
B Camera
C {CALL} button and indicator
L
The indicator is lighted with a red LED
while the power is on.
while the power is on.
L
When a visitor presses the call button,
a ringer tone will ring.
a ringer tone will ring.
D Water drain holes
L
These holes allow rain water to drain.
Do not cover them.
Do not cover them.
E Panel
F Speaker
G Microphone
F Speaker
G Microphone
A
B
C
D
E
F
G
N
Door station image quality
The following phenomena may occur. They are not malfunctions.
L
L
If the sun can be seen, its center appears as a black dot.
L
At night or when there is poor lighting in the doorway, the image colors
become unclear. If there is a light in the doorway, the image may appear
greenish.
become unclear. If there is a light in the doorway, the image may appear
greenish.
L
During the daytime or if there is bright light in the doorway, the color of the
visitor’s clothing may appear differently to the actual color.
visitor’s clothing may appear differently to the actual color.
Before installation
To avoid malfunction or communication disturbances, do not install the door station
in the following locations:
in the following locations:
– Places where vibration or any other kind of impact occurs.
– Places near hydrogen sulfi de.
– Places near hydrogen sulfi de.
Installation position of the door station and camera range
N
Views when the camera is facing forwards at 0° (default).
L
Example: Installation height is 1450 mm (standard position).
Side view
Top view
Image range:
960 mm
960 mm
500 mm
87°
1450 mm
1810 mm
Center of
the door
station
the door
station
66°
650 mm
Image
range
range
1160 mm
500 mm
Note:
L
L
The measurements and angles are for reference purposes and may vary
depending on the environment.
depending on the environment.
L
If a strong light is shining on the door station, the visitor’s face may not be
distinguishable.
Do not place the door station in the following locations.
– Where most of the background is the sky.
– Where the background is a white wall, and direct sunlight will refl ect off it.
– Where direct sunlight will shine on the door station.
distinguishable.
Do not place the door station in the following locations.
– Where most of the background is the sky.
– Where the background is a white wall, and direct sunlight will refl ect off it.
– Where direct sunlight will shine on the door station.
L
Do not place the door station in the locations where echoing occurs, causing the
unit to beep frequently.
unit to beep frequently.
L
Make sure the rear of the door station is not subject to water.
Wire type and distance
L
Wire (between the main monitor station and the door station):
Type
Distance
Loop resistance
General cable CAT-3
Maximum 50 m
10 Ω or lower
General cable 22 AWG (ø 0.65) Maximum 100 m
The camera angle can be adjusted using the camera angle control lever on the
rear of the door station (step 3, “Installing the door station”), so that the image
range can be changed.
rear of the door station (step 3, “Installing the door station”), so that the image
range can be changed.
N
Side view when the camera is installed
lower than the standard position, and
facing upwards at 15°.
facing upwards at 15°.
L
Example: Installation height is 1100 mm.
N
Top view when the camera is facing
left or right at 15° *
1
.
L
Example: Camera angle faces left 15°.
Center of
the door
station
the door
station
1690 mm
1100 mm
66°
710 mm
500 mm
980 mm
Image
range
range
Image range:
1080 mm
1080 mm
810 mm
500 mm
87°
270 mm
*
1
If the camera points 15° upwards, the left or right angle is less than 7°.
Installing the door station
Important:
L
L
On the bottom surface of the door station, there are holes to allow water to
drain. Do not cover them up when installing.
drain. Do not cover them up when installing.
1
Remove the mounting base.
A Open the screw
cover.
TScrewdriver
Mounting base
B Loosen the
mounting screw.
Water drain
holes
holes
2
Attach the mounting base to the wall securely using the wood screws (3.8
mm x 20 mm).
mm x 20 mm).
L
Install the mounting base on a vertical fl at wall.
L
Before drilling, refer to “Before installation” for installation location.
83.5 mm
Wall
Wire (Not included)
Mounting base
Wood screws
3
Adjust the camera angle using the camera angle control lever.
Important:
L
L
When the camera angle is adjusted to the upper left or upper right, the
image may be slightly distorted.
image may be slightly distorted.
L
The angle can also be adjusted to
the left or upper left.
the left or upper left.
<Examples of camera angle>
<Facing forwards>
<Facing upwards>
<Facing right>
<Facing upper right>
Rear view
Camera angle
control lever
control lever
Left
(maximum 15°)
Right
(maximum 15°)
Upwards
(maximum 15°)
4
Connect the wire, then mount the door station to the mounting base.
A Unscrew the screws.
Push in the wire to the terminal connectors
(non polar), then tightly fasten the screws.
(non polar), then tightly fasten the screws.
Wire (connecting to the main monitor station)
C Fasten the screw,
then close the
screw cover.
screw cover.
B Mount the door station
to the mounting base.
Specifi cations
Power source:
Supplied by the main monitor station
Dimensions:
Approx. height 131 mm x width 99 mm x depth 36.5 mm
(Excluding protruding sections)
Mass (Weight):
Approx. 200 g
Operating environment: -10 °C to 50 °C, Up to 90 % RH (Relative Humidity) non
condensing
Installation method:
condensing
Installation method:
Wall mount (Wall mount base included)
External material:
Flame retardant ABS resin
Note:
L
L
Design and specifi cations are subject to change without notice.
L
The pictures and illustrations in these instructions may vary slightly from the
actual product.
actual product.
Cleaning
Clean the unit with a soft, dry cloth when cleaning. For excessive dirt, wipe the unit
with a slightly damp cloth.
with a slightly damp cloth.
Important:
L
L
Do not use anything containing alcohol, polish powder, powder soap,
benzine, thinner, wax, petroleum, or boiling water.
Also do not spray with insecticide, glass cleaner, or hair spray.
This could cause a change in color or quality.
benzine, thinner, wax, petroleum, or boiling water.
Also do not spray with insecticide, glass cleaner, or hair spray.
This could cause a change in color or quality.
PNQW2397ZA_VL-V566BX_工説.indd 1-2
PNQW2397ZA_VL-V566BX_工説.indd 1-2
2010/08/19 17:06:47
2010/08/19 17:06:47