Panasonic RQT7114-2Y 用户手册
RQT7114
10
Basic operations
Inserting-removing a disc or SD Memory Card
Rear panel
Front panel
With the label
face up
face up
Power lamp
Front panel
With the label
face up
face up
SD ACCESS
indicator
indicator
SD Memory Card
Inserting a disc
1. Press [POWER
OFF
ON] on the rear of unit
The unit power is on. The display comes on and the power lamp
lights.
lights.
2. Insert a disc
•Insert the disc flat and parallel into the CD slot, with the label up.
The unit will automatically load the disc.
•You cannot use an 8 cm disc.
Note
•Do not insert a disc when the power is off.
•Do not insert 2 or more discs.
•Do not try to insert the disc using unnecessary force that may bend
•Do not insert 2 or more discs.
•Do not try to insert the disc using unnecessary force that may bend
the disc. When the unit is loading or ejecting a disc, do not apply
opposing force to the disc. Not following the above steps may re-
sult in damage to the disc or unit.
opposing force to the disc. Not following the above steps may re-
sult in damage to the disc or unit.
Removing a disc
While stopped or while paused
1. Press [ CD EJECT]
•Press the button and the disc will come out.
•If you press while playing in TURNTABLE mode, a message ap-
•If you press while playing in TURNTABLE mode, a message ap-
pears in the display and play continues. Make sure to press af-
ter pausing play.
ter pausing play.
•If you do not remove the disc within approximately 10 seconds
the unit will automatically re-load the disc.
To remove
2. Press again
•Remove as indicated in the illustration
without touching the playing surface.
Forced disc eject
You can forcefully eject a disc when the disc does not eject even after
pressing [ CD EJECT].
pressing [ CD EJECT].
1. Press [POWER
OFF
ON] to turn the power off
2. Press [POWER
OFF
ON] again holding down
[ CD EJECT] to turn the power on, and then release
[ CD EJECT] after “DZ1200” appears in the display
[ CD EJECT] after “DZ1200” appears in the display
Inserting a SD Memory Card
1. Open the SD Memory Card slot lid
2. With the label on the card facing up and the notched
edge facing the unit, insert the card
3. Insert until the card locks into place
4. Close the lid
Removing a SD Memory Card
After confirming the SD ACCESS indicator is not flash-
ing, open the lid and press on the center of the SD
Memory Card to release the lock and pull the ejected
card out carefully, then close the lid.
ing, open the lid and press on the center of the SD
Memory Card to release the lock and pull the ejected
card out carefully, then close the lid.
•The SD ACCESS indicator flashes when the SD Memory Card
is being accessed. Do not turn off the power or try to open the lid
and remove the card while the indicator is flashing. (Doing so
may result in a loss of saved data.)
and remove the card while the indicator is flashing. (Doing so
may result in a loss of saved data.)
Note
•Make sure to always close the SD card slot lid.
If you try using when the lid is open, “NO SD CARD” or “SD LID
OPEN” will appear in the display and operation will not be pos-
sible.
OPEN” will appear in the display and operation will not be pos-
sible.
•You can use SD Memory Cards with capacities between 8 MB
and 1 GB on this unit. (
page 25)
Playable media
CD
SD Memory Card
(SD audio)
CD-DA audio that is finalized on a
CD-R or CD-RW
CD-R or CD-RW
MP3 files
(WMA is not supported)
(WMA is not supported)
Secure AAC
Secure MP3
(WMA is not supported)
(WMA is not supported)
25
12, 22
22
Reference
Page