Husqvarna 395XP 用户手册
34
– English
Engine
Cylinder volume, cu.in/cm
3
Cylinder bore, inch/mm
Stroke, inch/mm
Idle speed, rpm
Recommended max.
speed, unloaded, rpm
Power, kW/rpm
Stroke, inch/mm
Idle speed, rpm
Recommended max.
speed, unloaded, rpm
Power, kW/rpm
Ignition system
Manufacture
Type of ignition system
Spark plug
Type of ignition system
Spark plug
Electrode gap, inch/mm
Fuel and lubrication
system
system
Manufacturer
Carburetor type
Fuel capacity, US pint/litre
Oil pump capacity at 8500 rpm,
ml/min
Oil capacity, US pint/litre
Type of oil pump
Carburetor type
Fuel capacity, US pint/litre
Oil pump capacity at 8500 rpm,
ml/min
Oil capacity, US pint/litre
Type of oil pump
Weight
Without bar and chain, Lbs/kg
Chain/bar
Standard bar length, inches/cm
Recommended bar lengths,
inches/cm
Usable cutting length
inches/cm
Recommended bar lengths,
inches/cm
Usable cutting length
inches/cm
Chain speed at max.
power, m/sec
power, m/sec
Pitch, inch/mm
Thickness of drive link,
inch/mm
inch/mm
Number of teeth on drive
sprocket
sprocket
TECHNICAL DATA
395XP
5,7/94
2,2/56
1,5/38
2 500
2,2/56
1,5/38
2 500
12 500
5,2/ 9 600
5,2/ 9 600
SEM
CD
Champion
RCJ 7Y
0,020"/0,5
CD
Champion
RCJ 7Y
0,020"/0,5
Tillotson
HS 298 A
1,9/0,9
HS 298 A
1,9/0,9
14-21
0,9/0,5
Automatic
0,9/0,5
Automatic
17,4/7,9
18"/45
18-36"/45-90
17-35"/44-88
21,4
3/8" / 9,52
0,404"/10,26
0,404"/10,26
0,050"/1,3
0,058"/1,5
0,063"/1,6
0,058"/1,5
0,063"/1,6
7
Recommended original and replacement bar
and chain combinations
and chain combinations
This Husqvarna saw model is in the ANSI category of saws
above 3,8 cu. in. and are not
above 3,8 cu. in. and are not
required
to comply with low
kickback performance requirements. However, for the
Husqvarna chain saw model 395XP we recommend the
following cutting equipment.
Husqvarna chain saw model 395XP we recommend the
following cutting equipment.
Guide bar
Saw chain
Length
Pitch
Max nose
inch
inch
radius
18-36
3/8
11T
Husqvarna H42 / S48 or
18-36
3/8
ATM 1,33"
Oregon 73LP / 73LG
Listed ATM is the Oregon designation of Armour Tip Medium hard nose bar.
The combinations of power head, bar and chain have been
investigated in accordance with the vibration requirements
of ANSI B 175.1-1991.
investigated in accordance with the vibration requirements
of ANSI B 175.1-1991.
Note: For the chains above you are free to choose
between 0,050", 0,058" and 0,063" gauge drive link for the
corresponding bar, see the table below.
between 0,050", 0,058" and 0,063" gauge drive link for the
corresponding bar, see the table below.
0,050"/1,3mm
–
72LP
72LG
0,058"/1,5mm
H42/73LP S48/73LG
–
0,063"/1,6 mm
–
75LP
75LG
´*2•=¶5Y¨