Husqvarna 1151375-95 用户手册
MAINTENANCE
30 – English
High speed jet H
•
The high speed jet H affects the power and speed of
the machine. If the high speed jet is set too lean
(screwed in too far) it will cause the machine to over-
rev and damage the engine. Turn the high speed jet H
anticlockwise until it stops. If the engine runs
unevenly, turn the high speed jet clockwise until the
engine runs evenly.
the machine. If the high speed jet is set too lean
(screwed in too far) it will cause the machine to over-
rev and damage the engine. Turn the high speed jet H
anticlockwise until it stops. If the engine runs
unevenly, turn the high speed jet clockwise until the
engine runs evenly.
•
The high speed jet H is correctly adjusted when the
machine burbles slightly. If the machine ”screams”,
the setting is too lean. If the muffler emits a lot of
smoke and the machine burbles a lot, the setting is too
rich. Turn the high speed jet H clockwise to achieve a
setting that sounds right.
machine burbles slightly. If the machine ”screams”,
the setting is too lean. If the muffler emits a lot of
smoke and the machine burbles a lot, the setting is too
rich. Turn the high speed jet H clockwise to achieve a
setting that sounds right.
CAUTION! To adjust the carburetor correctly you should
contact a mechanic with access to a rev counter.
contact a mechanic with access to a rev counter.
Correctly adjusted carburetor
When the carburetor is correctly adjusted the machine
accelerates without hesitation and the machine 4-cycles a
little at maximum speed. It is also important that the chain
does not rotate at idle. If the L-jet is set too lean it may
cause starting difficulties and poor acceleration. If the H-
jet is set too lean the machine will have less power, poor
acceleration and could suffer damage to the engine. If the
L and H-jets are set too rich it will lead to acceleration
problems or too low a working speed.
accelerates without hesitation and the machine 4-cycles a
little at maximum speed. It is also important that the chain
does not rotate at idle. If the L-jet is set too lean it may
cause starting difficulties and poor acceleration. If the H-
jet is set too lean the machine will have less power, poor
acceleration and could suffer damage to the engine. If the
L and H-jets are set too rich it will lead to acceleration
problems or too low a working speed.
Checking, maintaining and
servicing chain saw safety
equipment
servicing chain saw safety
equipment
Chain brake and front hand guard
Checking brake band wear
Brush off any wood dust, resin and dirt from the chain
brake and clutch drum. Dirt and wear can impair operation
of the brake.
brake and clutch drum. Dirt and wear can impair operation
of the brake.
Regularly check that the brake band is at least 0.024 inch
(0.6 mm) thick at its thinnest point.
(0.6 mm) thick at its thinnest point.
Checking the front hand guard
Make sure the front hand guard is not damaged and that
there are no visible defects such as cracks.
there are no visible defects such as cracks.
Move the front hand guard forwards and back to make
sure it moves freely and that it is securely anchored to the
clutch cover.
sure it moves freely and that it is securely anchored to the
clutch cover.
Checking the brake trigger
Place the chain saw on firm ground and start it. Make sure
the chain does not touch the ground or any other object.
See the instructions under the heading Start and stop.
the chain does not touch the ground or any other object.
See the instructions under the heading Start and stop.
Grasp the chain saw firmly, wrapping your fingers and
thumbs around the handles.
thumbs around the handles.
Apply full throttle and activate the chain brake by tilting
your left wrist forward onto the front hand guard. Do not let
your left wrist forward onto the front hand guard. Do not let
Note! All servicing and repair work on the machine
requires special training. This is especially true of the
machine
requires special training. This is especially true of the
machine
′
s safety equipment. If your machine fails any of
the checks described below we recommend you to
contact our servicing dealer.
contact our servicing dealer.