Husqvarna RS52 用户手册
14 –
English
ASSEMBLY
Assembling the cutting equipment
Fitting a blade guard, grass blade
and grass cutter
and grass cutter
•
The blade guard (A) is fitted using 4 screws (L) and the
support plate (M) as shown.
support plate (M) as shown.
CAUTION! Always use the recommended guard for the
cutting attachment you are using. See chapter on
Technical data.
cutting attachment you are using. See chapter on
Technical data.
•
Fit the drive disc (B) on the output shaft.
•
Turn the blade shaft until one of the holes in the drive disc
aligns with the corresponding hole in the gear housing.
aligns with the corresponding hole in the gear housing.
•
Insert the locking pin (C) in the hole to lock the shaft.
•
Place the blade (D) on the output shaft.
•
Fit the support flange (F) on the output shaft. Make sure
that the blade is centered by fitting it to the guide on the
support flange.
that the blade is centered by fitting it to the guide on the
support flange.
•
Screw the support cup (E) onto the output shaft threads
(CAUTION! Left-hand thread). Tighten to a torque of 35-
50 Nm (3.5-5.0 kpm). Use the socket spanner in the tool
kit. Note that the locking pin (C) must remain inside the
gear housing to lock the drive disk. Hold the shaft of the
socket spanner as close to the blade guard/combination
guard as possible.
(CAUTION! Left-hand thread). Tighten to a torque of 35-
50 Nm (3.5-5.0 kpm). Use the socket spanner in the tool
kit. Note that the locking pin (C) must remain inside the
gear housing to lock the drive disk. Hold the shaft of the
socket spanner as close to the blade guard/combination
guard as possible.
Fitting the blade guard and saw
blade
blade
•
The blade guard (A) is fitted using 4 screws (L) as shown.
CAUTION! Always use the recommended guard for the
cutting attachment you are using. See chapter on
Technical data.
cutting attachment you are using. See chapter on
Technical data.
•
Fit the drive disc (B) on the output shaft.
•
Turn the blade shaft until one of the holes in the drive disc
aligns with the corresponding hole in the gear housing.
aligns with the corresponding hole in the gear housing.
•
Insert the locking pin (C) in the hole to lock the shaft.
•
Place the blade (D) and support flange (F) on the output
shaft.
shaft.
•
Fit the nut (G). The nut must be tightened to a torque of
35-50 Nm (3.5-5 kpm). Use the socket spanner in the tool
kit. Hold the shaft of the spanner as close to the blade
35-50 Nm (3.5-5 kpm). Use the socket spanner in the tool
kit. Hold the shaft of the spanner as close to the blade
!
WARNING!
When fitting the cutting attachment it is
extremely important that the raised section
on the drive disc/support flange engages
correctly in the centre hole of the cutting
attachment. If the cutting attachment is fitted
incorrectly it can result in serious and/or
fatal personal injury.
extremely important that the raised section
on the drive disc/support flange engages
correctly in the centre hole of the cutting
attachment. If the cutting attachment is fitted
incorrectly it can result in serious and/or
fatal personal injury.
!
WARNING! Never use a cutting attachment
without an approved guard. See the chapter
on Technical data. If an incorrect or faulty
guard is fitted this can cause serious
personal injury.
without an approved guard. See the chapter
on Technical data. If an incorrect or faulty
guard is fitted this can cause serious
personal injury.
IMPORTANT! If a saw blade or grass blade are to be used
the machine must be equipped with the correct handlebar,
blade guard and harness.
the machine must be equipped with the correct handlebar,
blade guard and harness.
M
E
N
F
D
B
C
A
L
!
WARNING! Tighten the lock screw (N) in the
center hole of the support cup. Tighten to a
torque of 35-50 Nm (3.5-5.0 kpm), CAUTION!
Left-hand thread. If the lock screw is not
fitted in the support cup, there is a risk that
the support cup will come unscrewed. This
means that the blade will also come loose,
which could result in serious or fatal injury
to the operator or others.
center hole of the support cup. Tighten to a
torque of 35-50 Nm (3.5-5.0 kpm), CAUTION!
Left-hand thread. If the lock screw is not
fitted in the support cup, there is a risk that
the support cup will come unscrewed. This
means that the blade will also come loose,
which could result in serious or fatal injury
to the operator or others.
L
A