Rover 300361 用户手册
3
24
HEIGHT ADJUSTMENT – To cut lower, slacken quadrant clamp bolt nuts (1), also the lower
adjusting screw nut (2). Then tighten top adjusting screw nut (3) until desired height of cut is
obtained. To cut higher, reverse procedure. Re-tighten all nuts after desired setting is obtained. The
indicator marks on the quadrant are an indication of the cutting height, but to set the height of cut
accurately the setting gauge must be used. Refer setting gauge instructions.
adjusting screw nut (2). Then tighten top adjusting screw nut (3) until desired height of cut is
obtained. To cut higher, reverse procedure. Re-tighten all nuts after desired setting is obtained. The
indicator marks on the quadrant are an indication of the cutting height, but to set the height of cut
accurately the setting gauge must be used. Refer setting gauge instructions.
SETTING GAUGE – This illustrates the method of setting the gauge to the height of cut, where in
this instance height of cut is a twenty cent piece and a five cent coin. The distance between the
setting gauge bar and the underside of the adjustable screw head represents the height of cut. Lock
the screw in the desired position with the wing nut. To use the setting gauge, rest it against the
underside of the front and rear rollers, as illustrated, and by adjusting the front roller, the desired
height of cut will be obtained when the underside of the screw head lightly touches the top cutting
edge of the bottom blade across its full width. When using the setting gauge, take care not to force
the head of the adjusting screw onto the bottom blade, as this could distort the blade and affect
the setting.
this instance height of cut is a twenty cent piece and a five cent coin. The distance between the
setting gauge bar and the underside of the adjustable screw head represents the height of cut. Lock
the screw in the desired position with the wing nut. To use the setting gauge, rest it against the
underside of the front and rear rollers, as illustrated, and by adjusting the front roller, the desired
height of cut will be obtained when the underside of the screw head lightly touches the top cutting
edge of the bottom blade across its full width. When using the setting gauge, take care not to force
the head of the adjusting screw onto the bottom blade, as this could distort the blade and affect
the setting.
30” QUEEN
TM
- SPARE PARTS LIST
ITEM
PART No.
DESCRIPTION
1
A80084
Electric motor
2
305584
Plug mounting bracket
3
1661150
Plug- male
4
1661775
Cable clamp
5
1551265
Plastic conduit- flexible
6
A20207
Electrical wire- red
7
A20206
Electrical wire- black
8
306368
Cable gland
9
1661235
Plug- female
10
303124
Conduit clip
11
A20211
Switch
12
306341
Motor cover assembly
13
305373
Conduit
14
A20209
Earth wire
15
A20208
Earth wire
16
301649
Decal- warning
17
509819
Decal- Scott Bonnar
18
318228
Setscrew- 1/4” x 3/4” unf.HT.
19
2062724
Screw- 3/16” x 1” cheese head M/T.
20
A02050
Nut- 3/16” square pressed
21
2061886
Screw- 3/16” x 1/2” cheese head M/T.
22
A02216
Washer- 3/16” x 1/2” x 20g.flat
23
A02193
Nyloc nut- 3/16” unc.thin
24
A02163
Screw- 3/16” x 1/2” mush.head M/T.
25
A02023
Nut- 5/32” unc.hex.
26
A02039
Washer- 5/32” shakeproof
27
2072711
Screw- 5/32” x 1” bsw.csk.
28
A02044
Washer- 1/4” shakeproof
29
232116
Nut- 1/4” unf.hex.
30
A02017
Screw- 1/4” x 1/2” unc.Slotted Mush.head.
31
A02209
Washer- 1/4” x 5/8” x 18g.flat
32
A02235
Nyloc nut- 1/4” unc.
33
655533
Reset cover
34
A20044
Reset switch
35
A20210
Trip wire
36
A20213
Electrical wire- red reset switch
3676 Queen 30 Reel Mower.indd 4
22/11/2005 4:27:33 PM