Husqvarna YTH1342XP 用户手册
7
ASSEMBLY
TO SET UP YOUR MOWER FOR MULCH ING
• Remove high performance blades and install mulcher
blades, (see BLADE RE MOV AL in the Maintenance
sec tion of this manual).
sec tion of this manual).
YOUR MOWER CAME FACTORY EQUIPPED WITH HIGH
PERFORMANCE BLADES, WHICH ARE THE BEST BLADES
FOR BAGGING AND DISCHARGING. TO USE YOUR MOWER
WITH THE HIGH PERFORMANCE BLADES THE MULCHER
PLATE MUST BE REMOVED FROM THE MOWER (SEE FIG.
4).
PERFORMANCE BLADES, WHICH ARE THE BEST BLADES
FOR BAGGING AND DISCHARGING. TO USE YOUR MOWER
WITH THE HIGH PERFORMANCE BLADES THE MULCHER
PLATE MUST BE REMOVED FROM THE MOWER (SEE FIG.
4).
IMPORTANT: FOR SHIPPING PURPOSES, THE MULCHER
PLATE WAS PREATTACHED TO YOUR MOWER. THE MULCHER
PLATE MUST ONLY BE USED WITH THE MULCHING BLADES
THAT CAME PACKED SEPARATELY IN THE CARTON.
PLATE WAS PREATTACHED TO YOUR MOWER. THE MULCHER
PLATE MUST ONLY BE USED WITH THE MULCHING BLADES
THAT CAME PACKED SEPARATELY IN THE CARTON.
SEAT PAN
SHOULDER
BOLT
BOLT
ADJUSTMENT KNOB
FLAT WASHER
SEAT
FIG. 3
INSTALL SEAT (See Fig. 3)
Adjust seat before tightening adjustment knob.
• Remove adjustment knob and fl at washer securing
• Remove adjustment knob and fl at washer securing
seat to cardboard packing and set aside for assembly
of seat to tractor.
of seat to tractor.
• Pivot seat upward and remove from the cardboard pack-
ing. Remove the cardboard packing and discard.
• Place seat on seat pan so head of shoulder bolt is
positioned over large slotted hole in pan.
• Push down on seat to engage shoulder bolt in slot and
pull seat towards rear of tractor.
• Pivot seat and pan forward and assemble adjustment
knob and fl at washer loosely. Do not tighten.
Lower seat into operating position and sit on seat.
• Slide seat until a comfortable position is reached
• Slide seat until a comfortable position is reached
which allows you to press clutch/brake pedal all the
way down.
way down.
• Get off seat without moving its ad just ed position.
• Raise seat and tighten adjustment knob securely.
• Raise seat and tighten adjustment knob securely.
NOTE: You may now roll or drive your tractor off the skid.
Follow the appropriate instruction below to remove the
tractor from the skid.
Follow the appropriate instruction below to remove the
tractor from the skid.
TO ROLL TRACTOR OFF SKID (See Op-
er a tion section for location and function of
con trols)
er a tion section for location and function of
con trols)
• Release parking brake by de press ing clutch/brake
ped al.
• Place freewheel control in "trans mis sion dis en gaged
position" (See “TO TRANS
PORT” in the Op
er a tion
section of this manual).
• Roll tractor forward off skid.
• Remove banding holding the defl ector shield up against
• Remove banding holding the defl ector shield up against
tractor.
TO DRIVE TRAC
TOR OFF SKID (See Op-
er a tion section for location and function of
con trols)
con trols)
WARNING: Before start ing, read, un der stand and fol low
all in struc tions in the Op er a tion section of this man u al. Be
sure tractor is in a well-ventilated area. Be sure the area in
front of tractor is clear of other peo ple and objects.
• Be sure all the above assembly steps have been com-
sure tractor is in a well-ventilated area. Be sure the area in
front of tractor is clear of other peo ple and objects.
• Be sure all the above assembly steps have been com-
pleted.
• Check engine oil level and fi ll fuel tank with gasoline.
• Place freewheel control in "trans
• Place freewheel control in "trans
mis sion en
gaged"
po si tion (see "TO TRANSPORT" in Op er a tion section
of this manual).
of this manual).
• Sit on seat in operating position, depress clutch/brake
pedal and set the parking brake.
• Place motion control lever in neutral (N) position.
• Press lift lever plunger and raise attachment lift lever
• Press lift lever plunger and raise attachment lift lever
to its highest position.
• Start the engine. After engine has started, move throttle
control to idle position.
• Release parking brake.
• Slowly move the mo tion control lever for ward and slowly
• Slowly move the mo tion control lever for ward and slowly
drive tractor off skid.
• Apply brake to stop trac tor, set park ing brake and place
motion con trol lever in neutral po si tion.
• Turn ignition key to "STOP" position.
Continue with the in struc tions that follow.