Husqvarna 532 43 86-44 用户手册

Always observe safety rules when per form ing any main-

 te nance.

If tractor requires more than five (5) feet to stop at highest 

speed in high est gear on a level, dry concrete or paved sur-

face, then brake must be serviced. (See “TO CHECK BRAKE” 

in the Ser vice and Ad just ments section of this manual).

•  Maintain proper air pressure in all tires (See PSI on 

tires).

• 

Keep tires free of gasoline, oil, or insect control chemi-

 cals which can harm rubber.

•  Avoid stumps, stones, deep ruts, sharp objects and 

other hazards that may cause tire damage.

NOTE: To seal tire punctures and pre vent flat tires due 

to slow leaks, tire sealant may be purchased from your 

local parts dealer. Tire sealant also pre vents tire dry rot 

and corrosion.
OPERATOR PRESENCE SYS TEM AND REVERSE OP-

ERATION SYSTEM (ROS)
Be sure operator presence and reverse operation sys tems 

are work ing properly.  If your tractor does not function as 

described, repair the problem immediately.
•  The engine should not start unless the brake pedal is 

fully de pressed, and the attachment clutch con trol is 

in the dis en gaged position.

CHECK OPERATOR PRESENCE SYSTEM

• 

When the engine is running, any attempt by the op er a tor 

to leave the seat without first setting the parking brake 

should shut off the engine.

• 

When the engine is running and the at tach ment clutch 

is engaged, any attempt by the operator to leave the 

seat should shut off the engine.

•  The attachment clutch should never operate unless 

the operator is in the seat.

CHECK REVERSE OPERATION (ROS) SYSTEM

•  When the engine is running with the ignition switch in 

the engine "ON" position and the at tach ment clutch 

engaged, any attempt by the operator to shift into 

reverse should shut off the engine.

•  When the engine is running with the ignition switch in 

the ROS "ON" position and the at tach ment clutch en-

gaged, any attempt by the operator to shift into reverse 

should NOT shut off the engine.

For best results mower blades must be sharp.  Re place 

worn, bent or damaged blades.

02828

ROS "ON" Position

Engine "ON" Position

(Normal Operating)

•  Raise mower to highest position to allow access to 

blades.

NOTE: Protect your hands with gloves and/or wrap blade 

with heavy cloth.
•  Remove blade bolt by turning coun ter clock wise.
• 

Install new blade with stamped "GRASS SIDE" facing 

the ground.

IMPORTANT: To ensure proper as sem bly, center hole in 

blade must align with star on mandrel assembly.
•  Install and tighten blade bolt securely (45-55 Ft. Lbs. 

torque).

IMPORTANT:  Special blade bolt is heat treated.

Your tractor has a battery charging system which is suf fi cient 

for normal use.  However, periodic charging of the battery 

with an automotive charger will extend its life.
•  Keep battery and terminals clean.
•  Keep battery bolts tight.
•  Keep small vent holes open.
•  Recharge at  6-10 amperes for 1 hour.
NOTE: The original equipment battery on your tractor is 

maintenance free. Do not attempt to open or remove caps 

or covers. Adding or checking level of electrolyte is not 

necessary.
TO CLEAN BATTERY AND TERMINALS
Corrosion and dirt on the battery and terminals can cause 

the battery to “leak” power.
•  Remove terminal guard.
•  Disconnect BLACK battery cable first  then RED  bat-

 tery cable and remove battery from tractor.

•  Rinse the battery with plain water and dry.
• 

Clean terminals and battery cable ends with wire brush 

until bright.

•  Coat terminals with grease or petroleum jelly.
•  Reinstall battery (See “REPLACING BATTERY" in 

the SERVICE AND ADJUSTMENTS section of this 

man u al).