Husqvarna Z254 用户手册
Anti-scalp Rollers
Anti-scalp rollers are properly adjusted when they are just
slightly off of the ground when the deck is at the desired
cutting height in the operating position. Anti-scalp rollers then
keep the deck in the proper position to help prevent scalping
in most terrain conditions.
The anti-scalp rollers can be set in three positions:
slightly off of the ground when the deck is at the desired
cutting height in the operating position. Anti-scalp rollers then
keep the deck in the proper position to help prevent scalping
in most terrain conditions.
The anti-scalp rollers can be set in three positions:
• Upper position 1½" to 2½" (38 to 64 mm) grass
• Middle position 2½" to 4" (64 to 102 mm) grass
• Lower position 4" to 6" (102 to 128) mm grass.
• Middle position 2½" to 4" (64 to 102 mm) grass
• Lower position 4" to 6" (102 to 128) mm grass.
The rollers should be approximately ¼" (6.5 mm) from the
ground.
ground.
Caster Wheels
Check every 200 hours. Check that wheels rotate freely. If
wheels do not rotate freely take the unit to your dealer for
service.
Foam filled tires or solid tires will void the warranty.
Removal and installation
Remove nut and caster bolt. Pull the wheel out of the yoke and
take care of the spacers. Install in reverse order. Tighten caster
bolt.
wheels do not rotate freely take the unit to your dealer for
service.
Foam filled tires or solid tires will void the warranty.
Removal and installation
Remove nut and caster bolt. Pull the wheel out of the yoke and
take care of the spacers. Install in reverse order. Tighten caster
bolt.
IMPORTANT INFORMATION Adjust anti-scalp rollers with
the mower on a flat level surface.
To avoid deck damage, the anti-scalp rollers must not be
adjusted to support the deck.
the mower on a flat level surface.
To avoid deck damage, the anti-scalp rollers must not be
adjusted to support the deck.
V-belts
Check every 100 hours of operation. Check for severe
cracking and large nicks.
NOTE: The belt will show some small cracks in normal
operation.
The belts are not adjustable. Replace belts if they begin to slip
from wear.
Deck Belt Removal
1. Park on a level surface. Apply parking brake.
2. Lower the deck into the lowest cutting position.
3. Remove bolts from belt shields and remove shields.
4. Remove any dirt or grass that may have accumulated
cracking and large nicks.
NOTE: The belt will show some small cracks in normal
operation.
The belts are not adjustable. Replace belts if they begin to slip
from wear.
Deck Belt Removal
1. Park on a level surface. Apply parking brake.
2. Lower the deck into the lowest cutting position.
3. Remove bolts from belt shields and remove shields.
4. Remove any dirt or grass that may have accumulated
around the cutter housings and entire deck surface.
5. Remove tension on the belt by moving the idler arm.
6. Carefully slip belt up over the top of the cutter housing
6. Carefully slip belt up over the top of the cutter housing
pulleys and remove belt. Rolling belt over the pulleys may
damage the belt.
damage the belt.
Deck Belt Installation
NOTE: For ease in installing the deck belt, refer to the
routing decal on the top of the deck.
routing decal on the top of the deck.
1. Wrap the deck belt around the electric clutch pulley that is
located on the engine shaft.
2. Route the belt forward and up onto the deck.
3. Place belt around spring loaded idler pulley.
3. Place belt around spring loaded idler pulley.
4. Wrap the belt around the stationary idler pulley and
around the mandrel housings.
5. Push inward on the idler arm and carefully route belt over
stationary idler pulley. Once belt is properly routed, slowly
release idler arm to tension belt.
release idler arm to tension belt.
6. Double check belt routing to make sure it matches the
routing decal, and the belt does not have any twist.
Correct as needed.
Correct as needed.
7. Replace belt shields on both mandrel housings and
secure with fasteners.
24
MAINTENANCE