Husqvarna YTH2548XP 用户手册
6
ASSEMBLY
FIG. 2
ADJUST SEAT (See Fig. 2)
•
Sit in seat.
•
Lift up adjustment lever (A) and slide seat until a com-
fortable position is reached which allows you to press
clutch/brake pedal all the way down.
fortable position is reached which allows you to press
clutch/brake pedal all the way down.
•
Release lever to lock seat in position.
NOTE: You may now roll or drive your tractor off the skid.
Follow the ap pro pri ate instruction below to remove the
tractor from the skid.
Follow the ap pro pri ate instruction below to remove the
tractor from the skid.
WARNING: Before start ing, read, un der stand and fol low
all in struc tions in the Op er a tion section of this man u al. Be
sure tractor is in a well-ventilated area. Be sure the area in
front of tractor is clear of other peo ple and objects.
sure tractor is in a well-ventilated area. Be sure the area in
front of tractor is clear of other peo ple and objects.
TO ROLL TRACTOR OFF SKID (See Op-
er a tion section for location and function of
con trols)
er a tion section for location and function of
con trols)
•
Raise attachment lift lever to its highest po si tion.
•
Release parking brake by de press ing brake ped al.
•
Place freewheel control in dis en gaged po si tion to dis-
en gage trans mis sion (See “TO TRANS PORT” in the
Op er a tion section of this manual).
en gage trans mis sion (See “TO TRANS PORT” in the
Op er a tion section of this manual).
•
Roll tractor forward off skid.
TO DRIVE TRAC
TOR OFF SKID (See Op-
er a tion section for location and function of
con trols)
con trols)
•
Be sure all the above assembly steps have been com-
pleted.
pleted.
•
Check engine oil level and fill fuel tank with gasoline.
•
Place freewheel control in "trans
mis sion engaged"
position (see "TO TRANSPORT" in Operation section
of this manual).
of this manual).
•
Sit on seat in operating position, depress brake pedal
and set the parking brake.
and set the parking brake.
•
Raise attachment lift lever to its highest position.
•
Remove key from bag and start the engine (see "TO
START" in the Operation section of this manual). After
engine has started, move throttle control to idle (slow)
position.
START" in the Operation section of this manual). After
engine has started, move throttle control to idle (slow)
position.
•
Release parking brake.
A
Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping pur-
poses.
poses.
TOOLS REQUIRED FOR ASSEMBLY
A socket wrench set will make assembly easier. Stan dard
wrench sizes are listed.
wrench sizes are listed.
(1) 3/4" wrench
(1) Utility knife
(1) 9/16" wrench
(1) Pliers
(2) 7/16" wrenches
(1) Tire Pressure Gauge
When right or left hand is mentioned in this man ual, it
means from your point of view, when you are in the operat-
ing po si tion (seated be hind the steer ing wheel).
means from your point of view, when you are in the operat-
ing po si tion (seated be hind the steer ing wheel).
TO REMOVE TRACTOR FROM
CARTON
CARTON
UNPACK CARTON
•
Remove all accessible loose parts and parts cartons
from carton .
from carton .
•
Cut along dashed lines on all four panels of carton.
Remove end panels and lay side panels flat.
Remove end panels and lay side panels flat.
•
Remove mower and packing materials.
•
Check for any additional loose parts or cartons and
remove.
remove.
CONNECT BATTERY (See Figs. 1)
CAUTION: Do not short battery ter-
minals by allowing a wrench or any
other object to contact both terminals
at the same time. Before connect-
ing battery, remove metal bracelets,
wristwatch bands, rings, etc.
minals by allowing a wrench or any
other object to contact both terminals
at the same time. Before connect-
ing battery, remove metal bracelets,
wristwatch bands, rings, etc.
Positive terminal must be connected
first to prevent sparking from acci-
dental ground ing.
first to prevent sparking from acci-
dental ground ing.
•
Lift hood to raised position.
•
Remove terminal protective caps and discard.
•
If this battery is put into service after month and year
indicated on label (L) (label located between terminals)
charge battery for minimum of one hour at 6-10 amps.
(See "BATTERY" in the Maintenance section of this
manual for charg ing in struc tions).
indicated on label (L) (label located between terminals)
charge battery for minimum of one hour at 6-10 amps.
(See "BATTERY" in the Maintenance section of this
manual for charg ing in struc tions).
•
First connect RED battery cable to positive (+) terminal
with hex bolt and keps nut as shown. Tighten securely.
Slide terminal cover over terminal.
with hex bolt and keps nut as shown. Tighten securely.
Slide terminal cover over terminal.
•
Connect BLACK grounding cable to negative (-) ter-
minal with remaining hex bolt and keps nut. Tighten
securely.
minal with remaining hex bolt and keps nut. Tighten
securely.
FIG. 1
02954
L