Husqvarna 917.384507 用户手册

2

Safe ty Rules ..........................................2-3
Warranty ................................................4-7
Prod uct Spec i fi  

ca tions .............................. 8

Assembly / Pre-Operation ........................ 9
Op er a tion ...........................................10-13

Maintenance Sched ule ........................... 14
Maintenance ......................................14-16
Ser vice and Ad just ments ...................17-18
Stor age ..............................................18-19
Trou ble shoot ing .................................19-20
Re pair Parts .......................................40-47

IMPORTANT:  This cutting machine is capable of amputating hands and feet and throwing ob-
jects. Failure to observe the following safety instructions could result in serious injury or death.

 Look for this symbol to point out im-

 por tant safety precautions. It means
CAU TION!!!   BECOME ALERT!!!
YOUR SAFE TY IS INVOLVED.

  WARNING:  In order to prevent ac ci den tal 

starting when setting up, trans port ing, ad-
 just ing or making repairs, always dis con nect 
spark plug wire and place wire where it can not 
come in contact with plug. 

 WARNING: Engine exhaust, some of its 

constituents, and certain vehicle com po -
nents contain or emit chem i cals known to 
the State of Cal i for nia to cause can cer and 
birth defects or oth er re pro duc tive harm.

 WARNING: Battery posts, terminals and 

related accessories contain lead and lead 
compounds, chemicals known to the State 
of Cal i for nia to cause can cer and birth 
defects or oth er re pro duc tive harm. Wash 
hands after handling.

  CAUTION:  Muffl er and other engine 

parts become extremely 
hot during operation and 
remain hot after engine
has stopped. To avoid 
severe burns on contact, 
stay away from these areas.

•  Read, understand, and follow all 

in struc tions on the machine and in the 
manual(s) before starting. Be thor ough ly 
familiar with the controls and the proper 
use of the machine before starting.

•  Do not put hands or feet near or under 

rotating parts. Keep clear of the dis-
 charge opening at all times.

•  Only allow responsible individuals, who 

are familiar with the in struc tions, to 
operate the machine.

•  Clear the area of objects such as rocks, 

toys, wire, bones, sticks, etc., which could 
be picked up and thrown by blade.

•  Be sure the area is clear of other people 

before mowing. Stop the ma chine if 
anyone enters the area.

•  Do not operate the mower when bare-

 foot or wearing open sandals. Al ways 
wear substantial foot wear.

•  Do not pull mower backwards unless abso-

lutely nec es sary. Always look down and be-
hind before and while moving backwards.

•  Never direct discharged material toward 

anyone. Avoid discharging material 
against a wall or obstruction.  Material may 
richochet back toward the operator.  Stop 
the blade when crossing gravel surfaces.

•  Do not operate the mower without  prop-

er guards, plates, grass catcher or oth er 
safety protective devices in place.

•  See manufacturer’s instructions for 

proper operation and installation of 
accessories. Only use accessories ap-
proved by the manufacturer.

•  Stop the blade(s) when crossing grav el 

drives, walks, or roads.

•  Stop the engine (motor) whenever you 

leave the equip ment, before clean ing 
the mower or unclogging the chute.

•  Shut the engine (motor) off and wait 

until the blade comes to complete stop 
before removing grass catcher.

•  Mow only in daylight or good artifi cial light.
•  Do not operate the machine while under 

the infl uence of alcohol or drugs.

•  Never operate machine in wet grass. 

Always be sure of your footing: keep a 
fi rm hold on the handle; walk, never run.

•  Disengage the self-propelled mech-

 a nism or drive clutch on mowers so 
equipped before starting the engine.

•  If the equipment should start to vi brate 

abnormally, stop the engine (motor) and 
check immediately for the cause. Vibra-
tion is generally a warning of trouble.

•  Always wear safety goggles or safe ty glass-

es with side shields when op er at ing mower.

Slopes are a major factor related to slip & 
fall accidents which can result in severe 
injury. All slopes require extra caution. If 
you feel uneasy on a slope, do not mow it.

47

 CAMSHAFT PULLEY
 KEY     PART
NO.      NO. 

 1  14320-ZL8-010  Pulley, Camshaft
  2  14324-ZL8-000  Shaft, Cam Pulley
 3  14400-Z0J-014  Belt, Timing
   

(84HU7 

G-200)

 6  14461-ZL8-000  Shaft, Rocker Arm
 11 90112-333-000  Screw, Tappet Adjusting
 12 90206-001-000  Nut, Tappet Adjusting
 13  91301-ZM0-V31  O-Ring (6.8 x 1.9) (ARAI)
15  14431-Z0J-000  Rocker Arm, Intake Valve 
 16 14441-Z0J-000  Rocker Arm,
   

Exhaust 

Valve

 1  11300-ZM0-811  Pan Assembly, Oil
 2  15650-ZM0-801  Gauge Assembly,
   

Oil 

Level

  4  15625-ZE6-000  Gasket, Oil Filler Cap
  5  15631-ZM0-000  Extension, Oil Filler
  6  15639-ZM0-000  Lock Washer, Extension
  8  16508-ZM0-010  Shaft, Governor Holder
 9  16510-ZM0-010  Governor Assembly
 10 16511-ZL8-000  Weight, Governor
 11  16512-ZM0-000  Holder, Governor Weight
 12  16513-ZE1-000  Pin, Governor Weight
 13 16531-ZE1-000  Slider, Governor
 14 16541-ZM0-000  Shaft, Governor Arm
 15  90014-952-000  Bolt, Flange (#6 x 14)
   

(CT200)

 16  90121-952-000  Bolt, Flange (#6 x 25)
   

(CT200)

 17  90451-ZE1-000  Washer, Thrust (6 mm)
 18  90602-ZE1-000  Clip, Governor Holder
 19  91202-ZL8-003  Oil Seal (28 x 41.25 x 6)
 20  91356-MA6-005  O-Ring (14.8 x 2.4) (NOK)
 21  94101-068000 

Washer, Plain (6 mm)

 22  94251-08000 

Pin, Lock (8 mm)

 23  94301-08200 

Pin, Dowel (#8 x 20)

 1  13101-Z2A-010  Piston
 2  13111-ZE0-000  Pin, Piston
 3  13200-Z0J-000  Connecting Rod Assembly
  4  90001-ZE1-000  Bolt, Connecting Rod
  5  90551-ZE0-000  Clip, Piston Pin (13 mm)
  6  13010-Z0L-014  Ring Set, Piston, Standard
   

(Teikoku)

  9  87528-Z0L-V20  Mark, Choke Indication 
 20 87114-ZH7-821  Label, Warning
 30  87101-Z8B-000  Mark, Emblem (GCV160)
 31  87169-Z8E-000  Mark, Recoil Cover
 32 87524-Z8B-000  Mark, Caution,
   

Fuel 

Petcock

 
 CHOKE BASE
KEY     PART
NO.      NO. 

 2  16592-Z2D-800  Spring, Return
  5  16614-Z2D-800  Spring, Choke Lever
 8  16632-Z0L-801  Rod, Stop
  9  90022-888-010  Bolt, Flange (#6 x 20)
   

(CT200)

 14 16610-Z2D-801  Lever Assembly, Choke
  16610-Z2D-802 Lever 

Assembly, 

Choke