Husqvarna 917.37408 用户手册

6

Read these instructions and this manual in its entirety before you attempt to assemble or 
operate your new lawn mower.
IMPORTANT: This lawn mower is shipped WITHOUT OIL OR GASOLINE in the engine.
Your new lawn mower has been as sem bled at the factory with the exception of those parts 
left unassembled for shipping pur pos es.  To ensure safe and proper op er a tion of your lawn 
mower, all parts and hard ware you assemble must be tight ened securely.  Use the correct 
tools as nec es sary to ensure proper tightness.  All parts such as nuts, wash ers, bolts, etc., 
nec es sary to complete the as sem bly have been placed in the parts bag.

TO ASSEMBLE GRASS CATCH ER
1.   Put grass catcher frame into grass bag 

with rigid part of bag on the bottom. 
Make sure the frame handle is outside 
of the bag top.

2.   Slip vinyl bindings over frame.
NOTE:  If vinyl bindings are too stiff, hold 
them in warm water for a few minutes. If 
bag gets wet, let it dry before using.

TO INSTALL ATTACHMENTS 
Your lawn mower was shipped ready to be 
used as a mulcher. To convert mower to 
bagging or discharging, see “TO CON-
 VERT MOWER” in the Operation section 
of this manual.

Frame 

handle

Frame 

opening

Vinyl 
bindings

MOWING 

POSITION

Lower handle

LIFT 
UP

Operator 
presence 
control bar

Upper 

handle

LIFT 

UP

Handle 

knob

1.    Remove loose parts included with mower.
2.   Cut down two end corners of carton 

and lay end panel down fl at.

3.   Remove all packing materials except 

padding be tween upper and lower 
handle and padding holding operator 
presence control bar to upper handle.

4.   Roll lawn mower out of carton and 

check carton thor ough ly for additional 
loose parts. 

TO UNFOLD HANDLE
IMPORTANT:  Unfold handle carefully so 
as not to pinch or damage con trol cables. 
1.   Raise handles until lower handle sec-

tion locks into place in mowing position.

2.   Remove protective padding, raise up-

per handle sec tion into place on lower 
handle and tighten both handle knobs.

3.    Remove handle padding holding operator 

pres ence control bar to upper handle.

Your lawn mower handle can be adjusted 
for your mowing comfort. Refer to “AD-
 JUST HANDLE” in the Service and Adjust-
ments section of this manual.

43

PART NO.  QTY.  DESCRIPTION 
14 332 04-s  1 

Insert, Engine Cover (Black)

25 086 167-s  4 

Screw, #15, 6-Lobe,

 

 

Pan Head, Hi-Lo Thread

14 027 03-s  1 

Housing, Blower w/Elec Start 

14 096 27-s  1 

Cover, Engine (Black) 

25 086 288-s  2 

Screw, Shoulder (M5)

PART NO.  QTY.  DESCRIPTION 
14 109 02-s  1 

Cup, Drive

14 025 02-s  1 

Flywheel (Aluminum)

14 584 05-s  1 

Module, Ignition

 

 

(Aluminum Std. Ignition)

14 132 03-s  1 

Spark Plug

14 112 07-s  3 

Spacer

14 072 12-s  2 

Stud

14 072 13-s  1 

Stud

14 314 01-s   1 

Guard 

14 157 01-s  1 

Fan, Flywheel

14 219 07-s  1 

Brake Assembly, Carb Side

 

 

(Includes Brake Lever, Brake

 

 

Spring, Flange Nuts, Brake

 

 

Pad, Ground To Kill Lead,

 

 

Screw, Kill Switch, Brake

 

 

Bracket, Brake Lever

 

 

Washer, Brake Lever Rivet) 

14 100 10-s  1 

Nut, Flywheel (w/Serrations)

25 086 145-s  1 

Screw, Hex Flange (M6)

EXHAUST   
PART NO.  QTY.  DESCRIPTION 
14 314 04-s  1 

Shield, Muffl er

14 068 05-s  1 

Kit, Muffl er

  

(Includes 

Muffl er Gasket)

14 072 06-s  1 

Kit, Exhaust Hardware

  

(Includes 

Muffl er Gasket,

 

 

Exhaust Studs and

 

 

Flanged Lock Nuts)

PART NO.  QTY.  DESCRIPTION 
14 199 01-s  1 

Kit, Oil Pan (Includes

 

 

14 032 05-s, 14 041 06-s,

  

Governor 

Gear 

Assembly

 

 

and Dowel Pins)

14 032 05-s  1 

Seal, Oil (PTO)

14 041 06-s  1 

Gasket, Oil Pan

14 123 04-s  1 

Assembly, Dipstick And Tube

 

 

(Includes 14 153 01-s

 

 

and 14 153 03-s)

14 153 03-s  1 

O-ring, Oil Fill Tube

14 153 01-s  1 

O-ring, Dipstick

25 086 161-s  6 

Screw, Hex Flange (M8)

25 086 145-s  1 

Screw, Hex Flange (M6)

CRANKCASE  

 

PART NO.  QTY.  DESCRIPTION 
14 050 01-s  1 

Kit, Breather Filter (Includes

 

 

Breather Cover Gasket,

 

 

Breather Cover Spring,

  

Breather 

Filter

 

 

and Breather Reed)

14 067 01-s  1 

Connecting Rod

14 032 02-s  1 

Seal, Oil

14 032 04-s  1 

Seal, Oil

14 018 03-s  2 

Retainer, Piston Pin

CRANKSHAFT
PART NO.  QTY.  DESCRIPTION 
14 340 01-s  1 

Key, Flywheel

14 014 14-s  1 

Crankshaft Assembly