Husqvarna Rider 318 用户手册
26 –
English
Lubrication
Checking the engine’s oil level.
Check the oil level in the engine when the Rider stands
horizontal with the engine switched off. Do not check the oil
with the engine running.
horizontal with the engine switched off. Do not check the oil
with the engine running.
Open the engine cover.
Loosen the dipstick, pull it up and wipe it off.
Now insert the dipstick again. The dipstick should be
completely screwed down
completely screwed down
Pull the dipstick out again and read the oil level.
The oil level should be between the markings on the dipstick.
If the level is approaching the ADD mark, top up the oil to the
FULL mark on the dipstick.
If the level is approaching the ADD mark, top up the oil to the
FULL mark on the dipstick.
The oil is topped up through the hole the dipstick sits in. Fill
the oil slowly.
the oil slowly.
Tighten the dipstick correctly before starting the engine. Start
and run the engine at idling speed for approx. 30 seconds.
Turn off the motor. Wait 30 seconds and check the oil level. If
necessary fill so that the oil comes up to the FULL mark on
the dipstick.
and run the engine at idling speed for approx. 30 seconds.
Turn off the motor. Wait 30 seconds and check the oil level. If
necessary fill so that the oil comes up to the FULL mark on
the dipstick.
First and foremost use synthetic engine oil class SJ-CF 5W/
30 or 10W/30 for all temperature ranges. Mineral oil SAE30,
class SF–CC can be used at temperatures > +5
30 or 10W/30 for all temperature ranges. Mineral oil SAE30,
class SF–CC can be used at temperatures > +5
°C (40 °F)
Do not mix different types of oil.
Caution when using oils such as 5W-20, 10W-30 and 10W-40
the engine’s oil consumption increases. If these oils must be
used, check the oil level frequently.
the engine’s oil consumption increases. If these oils must be
used, check the oil level frequently.
Replacing the engine oil
The engine oil should be changed the first time after 8 hours
running time. It should then be changed after every 50 hours
of running time. When operating with a heavy load or at high
ambient temperatures, replace every 25 hours.
running time. It should then be changed after every 50 hours
of running time. When operating with a heavy load or at high
ambient temperatures, replace every 25 hours.
1
Place a container underneath the engine’s left oil drain
plug.
plug.
2
Remove the dipstick. Remove the drain plug from the
engine’s left side.
engine’s left side.
3
Let the oil run out into the container.
4
Fit the drain plug and tighten it.
5
If necessary fill so that the oil comes up to the FULL mark
on the dipstick. The oil is topped up through the hole the
dipstick sits in. See Checking the engine’s oil level for
filling instructions. The engine holds 1.4 litres (1.5 USqt)
when the oil filter is not replaced and 1.6 litres (1.7 USqt)
of oil when the oil filter is replaced.
on the dipstick. The oil is topped up through the hole the
dipstick sits in. See Checking the engine’s oil level for
filling instructions. The engine holds 1.4 litres (1.5 USqt)
when the oil filter is not replaced and 1.6 litres (1.7 USqt)
of oil when the oil filter is replaced.
6
Run the engine warm, then check that there is no leakage
from the oil plug.
from the oil plug.
Changing the oil filter
The oil filter must be replaced after every 200 hours running
time. Turn the old oil filter anti-clockwise to remove. If
necessary, use a filter remover.
time. Turn the old oil filter anti-clockwise to remove. If
necessary, use a filter remover.
Lightly lubricate the rubber seal on the new oil filter using new
oil. Fit the oil filter by turning clockwise. Turn by hand until the
rubber seal is seated. Now tighten a further half turn.
oil. Fit the oil filter by turning clockwise. Turn by hand until the
rubber seal is seated. Now tighten a further half turn.
Fill with new oil according to Checking the engine’s oil level.
Start the engine and let it idle for about 3 minutes. Now stop
it and check for signs of leakage. Fill with oil to compensate
for the oil held in the new oil filter.
Start the engine and let it idle for about 3 minutes. Now stop
it and check for signs of leakage. Fill with oil to compensate
for the oil held in the new oil filter.
!
WARNING! Engine oil can be very hot if it is
drained directly after stopping the engine.
Allow the engine to cool somewhat first.
drained directly after stopping the engine.
Allow the engine to cool somewhat first.
ADD
FULL
ADD
FULL
IMPORTANT INFORMATION
Used engine oil, antifreeze etc. is a health hazard and must
not be disposed of on the ground or in nature; it should
always be disposed of at a workshop or appropriate
disposal location.
not be disposed of on the ground or in nature; it should
always be disposed of at a workshop or appropriate
disposal location.
Avoid skin contact; wash with soap and water in case of
spills.
spills.