Husqvarna LTH140 用户手册
21
SERVICE AND ADJUSTMENTS
.012"
ROTOR
BRAKE PLATE
SLOT (3)
NYLON LOCKNUT (3)
CLUTCH PLATE
FIG. 26
TO ADJUST BRAKE (See Fig. 27)
Your tractor is equipped with an adjustable brake system
which is mounted on the right side of the transaxle.
which is mounted on the right side of the transaxle.
If tractor requires more than six (6) feet stopping distance
at high speed in highest gear, then brake must be adjusted.
at high speed in highest gear, then brake must be adjusted.
•
Depress clutch/brake pedal and engage parking brake.
•
Measure distance between brake operating arm and
nut "A" on brake rod.
nut "A" on brake rod.
•
If distance is other than 1-3/4", loosen jam nut and turn
nut "A" until distance becomes 1-3/4". Retighten jam
nut against nut "A".
nut "A" until distance becomes 1-3/4". Retighten jam
nut against nut "A".
•
Road test tractor for proper stopping distance as stated
above. Readjust if necessary. If stopping distance is
still greater than six (6) feet in highest gear, further
maintenance is necessary. Contact your nearest au-
thorized service center.
above. Readjust if necessary. If stopping distance is
still greater than six (6) feet in highest gear, further
maintenance is necessary. Contact your nearest au-
thorized service center.
WITH PARKING BRAKE "ENGAGED"
1-3/4"
JAM NUT
OPERATING ARM
NUT “A”
DO NOT TOUCH THIS NUT. IF FURTHER
BRAKE ADJUSTMENT IS NECESSARY,
CONTACT YOUR NEAREST AUTHORIZED
SERVICE CENTER/DEPARTMENT.
BRAKE ADJUSTMENT IS NECESSARY,
CONTACT YOUR NEAREST AUTHORIZED
SERVICE CENTER/DEPARTMENT.
FIG. 27
TO REPLACE MOWER BLADE DRIVE BELT
(See Fig. 25)
(See Fig. 25)
The mower blade drive belt may be replaced without tools.
Park the tractor on level surface. Engage parking brake.
Park the tractor on level surface. Engage parking brake.
BELT REMOVAL -
•
•
Remove mower from tractor (See “TO REMOVE
MOWER” in this section of this manual).
MOWER” in this section of this manual).
•
Work belt off both mandrel pulleys and idler pulleys.
•
Pull belt away from mower.
BELT INSTALLATION -
•
•
Install new belt in reverse order of removal.
•
Make sure belt is in all pulley grooves and inside all belt
guides.
guides.
•
Install mower in reverse order of removal instructions.
MANDREL
PULLEY
PULLEY
MANDREL PULLEY
FIG. 25
IDLER
PULLEYS
PULLEYS
TO ADJUST ATTACHMENT CLUTCH
(See Fig. 26)
(See Fig. 26)
The electric clutch should provide years of service. The
clutch has a built-in brake that stops the pulley within 5
seconds. Eventually, the internal brake will wear which
may cause the mower blades to not engage, or, to not stop
as required. Adjustments should be made by an authorized
service technician.
clutch has a built-in brake that stops the pulley within 5
seconds. Eventually, the internal brake will wear which
may cause the mower blades to not engage, or, to not stop
as required. Adjustments should be made by an authorized
service technician.
•
Make sure attachment clutch and ignition switches are
in “OFF” position.
in “OFF” position.
•
Adjust the three nylon locknuts until space between
clutch plate and rotor measures .012" at all three slot
locations cut in the side of brake plate.
clutch plate and rotor measures .012" at all three slot
locations cut in the side of brake plate.
NOTE: After installing a new electric clutch, run tractor at
full throttle and engage and disengage electric clutch 10
cycles to wear in clutch plate.
full throttle and engage and disengage electric clutch 10
cycles to wear in clutch plate.