Cub Cadet 190-670-100 用户手册
8
•
Attach the grass bags using the slots shown in
Figure 5. Close the grasscatcher cover.
Figure 5. Close the grasscatcher cover.
Attaching the Discharge Chute
•
Raise the deck to its highest position.
•
On older models: Remove the clip, if already
installed on the deck next to the discharge chute
opening, by removing the lock nut, spring washer
and hex bolt that secure it. See Figure 6A.
installed on the deck next to the discharge chute
opening, by removing the lock nut, spring washer
and hex bolt that secure it. See Figure 6A.
Figure 6
•
On older models: A grasscatcher pin (G in Figure
1) and nut (H in Figure 1) have been supplied in the
hardware pack. Attach these to the deck in place of
the clip just removed. Follow Figure 6B for order of
assembly. Make sure to secure the pin tightly.
1) and nut (H in Figure 1) have been supplied in the
hardware pack. Attach these to the deck in place of
the clip just removed. Follow Figure 6B for order of
assembly. Make sure to secure the pin tightly.
•
Raise the chute deflector on the deck and hold it
while you position the discharge chute over the
chute opening.
while you position the discharge chute over the
chute opening.
•
Place the top rear edge of the discharge chute over
the top rear edge of the chute opening.
the top rear edge of the chute opening.
•
Push down on the discharge chute so that its front
bottom edge rolls over the bottom of the deck; then
slide the chute forward to the stop on the deck. See
Figure 7.
bottom edge rolls over the bottom of the deck; then
slide the chute forward to the stop on the deck. See
Figure 7.
NOTE: The retainer strap is fitted at position B on the
discharge chute. However, on older models of tractors,
you may have to change the position of the strap
depending on the location of the grasscatcher pin on
the deck. Remove the retainer strap from position B on
the discharge chute to position A or C corresponding to
the position of the grasscatcher pin at A, B or C on the
deck. See Figure 7.
discharge chute. However, on older models of tractors,
you may have to change the position of the strap
depending on the location of the grasscatcher pin on
the deck. Remove the retainer strap from position B on
the discharge chute to position A or C corresponding to
the position of the grasscatcher pin at A, B or C on the
deck. See Figure 7.
Figure 7
•
Place the deck at its lowest position.
•
Lock the discharge chute in position by hooking the
retainer strap over the grasscatcher pin on the
deck. See Figure 7 for the pin position.
retainer strap over the grasscatcher pin on the
deck. See Figure 7 for the pin position.
•
Raise the deck back to its highest position.
•
Insert the curved end of chute tube into the hole in
the grass bag cover. See Figure 8.
the grass bag cover. See Figure 8.
Figure 8
•
Place the lower end of the chute tube over the
discharge chute so that the two notches on the
chute tube fit into the two corresponding notches on
the discharge chute. See Figure 9.
discharge chute so that the two notches on the
chute tube fit into the two corresponding notches on
the discharge chute. See Figure 9.
Figure 9
•
Secure by clipping the two retainer straps of the
discharge chute to the pins on the chute tube. See
Figure 9.
discharge chute to the pins on the chute tube. See
Figure 9.
Hex Bolt
Spring
Washer
Hex Lock
Cutting
Deck
Deck
Clip
Nut
Grasscatcher
Pin
Nut
Deck
A
B
Chute Deflector
Retainer Strap
C
A
B
C
A
B
Pin
Insert chute tube here
Chute
Tube
Tube
Retainer
Strap
Strap
Chute
Tube
Tube
Notch