Dimension One Spas Dynamic Massage Sequencer 用户手册

2002 Dimension One Spas Export Owner’s Manual 

 

Your Scrolling Message Center is the most advanced in the industry and can virtually walk you through customizing 
your hot tub to your exact needs. To initiate the programming sequence at any time, push and hold the Program 
pad for 3 seconds. If, within 10 seconds, you do not proceed with the hot tub programming, the hot tub will 
automatically exit the programming sequence and revert to the pre-set factory default settings. To exit the 
programming sequence at any time, push the Enter pad or do not press a pad for 10 seconds. Any programming 
changes made up to that point are saved. 

After holding the PROGRAM pad, the top line of the Digital Display will read “SET TIME OF DAY” and the 
bottom line will read “PUSH UP OR DOWN TO CHANGE - PUSH PROGRAM TO SELECT NEXT FUNCTION 
- PUSH ENTER TO EXIT ”. Push the UP or DOWN pads to engage the time setting mode. The time screen will 
appear with “hours” (_ _.00) flashing on and off. Push the UP or DOWN pad to increase or decrease the number 
until the desired hour appears. When the desired number is displayed, push the LIGHT pad to accept the selection 
and change the flashing number to the “ten minute” place (12:_0). Adjust the number with the UP or DOWN pad 
in the same manner as the hour number. When the desired indicator is displayed, push the LIGHT pad to accept 
the selection and change the flashing number to the “minute” place (12:1_). Adjust this number with the UP or 
DOWN pad in the same manner as the hour number. When the desired number is displayed, push the LIGHT pad 
to accept the selection and change the flashing number to a flashing AM or PM indicator. Adjust the indicator with 
the UP or DOWN pads. After reaching the correct time, push the PROGRAM pad to set the time and exit the 
time setting mode. You will then be prompted to set the filter start time. 

After setting the time-of-day, the top line of the Digital Display will read “SET FILTER CYCLE TIME”. Push the UP 
or DOWN pads in the same manner as setting the clock to select the time you want your filter cycle to start. 
When your desired filter cycle start time is set in the display, push the PROGRAM pad to continue. The pre-set 
factory default is 12:00 p.m. to 1:00 p.m. repeating every 12 hours unless the number of filter cycles per day has 
been changed. 
 

 

 

Keep in mind that you will later be prompted to set the filter cycle duration and the number of 
filter cycles. Be sure to keep this in mind when programming your filter cycle start time. 

 

During a filter cycle, the bottom left of the Digital Display will read “SPA FILTERING”. During the filter cycle, JETS 
1 will activate, the first 5 minutes at high speed and the remainder of the filter cycle time at low speed. JETS 2 will 
also activate for 1 minute on high speed and then turn off. 

After setting the filter cycle start time, the top line of the Digital Display will read “SET CYCLE DURATION”. 
Push the UP or DOWN pads to toggle between 60, 90, 120, 150 and 180 minutes. The first 5 minutes of the filter 
cycle will be at high speed and the remaining time at low speed. When your desired filter cycle length appears in 
the Digital Display, push the PROGRAM pad to select it. The pre-set factory default is 60 minutes. 

After setting the length of the filter cycle, you will be prompted to set the number of filter cycles. The top line of 
the Digital Display will read “SET # OF CYCLES”. Push the UP or DOWN pad to toggle from 1 to 2 to 3 to 4 
cycles per day. When your desired number of cycles appears on the Digital Display, push the PROGRAM pad to 
select it. The pre-set factory default is 2 cycles per day. 

 

 

Long and/or numerous filter cycles could cause overheating of the hot tub - especially in hot 
climates. 

 

16