Roland MC-909 用户手册
29
Playing a pattern
Pattern Mode
RPS Settings
1.
Hold down [RPS] and press [F6 (RPS Setting)].
Alternatively, hold down [SHIFT] and press [F4 (RPS)].
The RPS setting screen will appear.
2.
Use [CURSOR (up/down)] to select a parameter.
3.
Use [VALUE] or [INC/DEC] to edit the parameter.
<RPS Trigger Quantize>
When using RPS during pattern playback, patterns and phrases may
not play back in precise alignment, depending on the timing at
which you press the velocity pads. On the MC-909 you can specify
the playback timing of the phrase, so it will play back in precise
synchronization with the pattern. (RPS Trigger Quantize ->p. 128)
not play back in precise alignment, depending on the timing at
which you press the velocity pads. On the MC-909 you can specify
the playback timing of the phrase, so it will play back in precise
synchronization with the pattern. (RPS Trigger Quantize ->p. 128)
•
REAL:
The phrase will play back immediately, at the timing at which
you pressed velocity pads.
you pressed velocity pads.
•
16TH, 8TH, QUARTER:
The pattern will be divided into selected note units, and when
you press the velocity pads, the phrase will begin playing at the
beginning of the next note unit.
you press the velocity pads, the phrase will begin playing at the
beginning of the next note unit.
•
MEASURE:
The pattern will be divided into one-measure units, and when
you press the velocity pads, the phrase will begin playing at the
beginning of the next measure.
you press the velocity pads, the phrase will begin playing at the
beginning of the next measure.
*
Except when this parameter is set to “REAL,” pressing on the velocity
pads slightly before the actual desired timing will help you
synchronize the phrase to the pattern.
pads slightly before the actual desired timing will help you
synchronize the phrase to the pattern.
*
If the pattern is stopped, the phrase will play back immediately,
regardless of the setting that is selected in the above procedure.
regardless of the setting that is selected in the above procedure.
Adjusting the settings of the RPS parts
RPS playback uses dedicated RPS parts that are separate from
conventional pattern playback. The patterns that are assigned to
velocity pads [1]–[16] will play RPS parts 1–16.
conventional pattern playback. The patterns that are assigned to
velocity pads [1]–[16] will play RPS parts 1–16.
Here's how to adjust the settings of these RPS parts.
1.
Hold down [RPS] and press [F6 (RPS Setting)].
Alternatively, hold down [SHIFT] and press [F4 (RPS)].
The RPS setting screen will appear.
2.
Press [F3 (RPS Mixer)].
The RPS Mixer screen will appear.
3.
Use the part mixer section to adjust the volume, pan,
etc. of RPS parts 1–16.
Use [F1]--[F4] to select a parameter, and use the sliders to adjust
the values.
the values.
*
You can also use [CURSOR] to select a part and parameter, and then
use [VALUE] or [DEC/INC] to adjust the value.
use [VALUE] or [DEC/INC] to adjust the value.
4.
Press [F6 (Close)] to close the RPS Mixer screen.
Parameter
Range
Explanation
RPS Set
01–50
RPS set to edit
RPS Part
Part 1–16
RPS part to edit
RPS Part Patch
Bank
Bank
—
Patch assigned to RPS part
RPS Part Patch
Number
Number
—
RPS Part Output
Select
Select
DRY, MFX1,
MFX2,
COMP,
DIR1, DIR2,
RHY
MFX2,
COMP,
DIR1, DIR2,
RHY
How the original sound of
each part will be output
each part will be output
DRY:
Output to MIX OUT-
PUT jacks without passing
through effects
through effects
MFX1 (2):
Output through
multi-effects 1 (or 2)
COMP:
Output through
the compressor
DIR1 (2):
Output to the DI-
RECT 1 (or DIRECT 2)
jacks without passing
through effects
jacks without passing
through effects
RHY:
Output according to
the settings of the rhythm
set assigned to the part
set assigned to the part
Remote Key-
board Switch
board Switch
OFF, ON
[PART ASSIGN]
Selects the RPS parts that will be controlled
by the sliders.
by the sliders.
If this indicator is not lighted, parts 1–8
will be controlled. If lit, parts 9–16 will be
controlled.
will be controlled. If lit, parts 9–16 will be
controlled.
Sliders
Adjust the volume, pan, key, and reverb lev-
el of parts 1–8 or parts 9–16.
el of parts 1–8 or parts 9–16.
Function button
Parameter adjusted by the sliders
[F1 (Level)]
Volume of the RPS part
[F2 (Pan)]
Left/right position of the RPS part
[F3 (Key Shift)]
Transposition of the RPS part
The pitch will change in semitone steps
over a range of +/-4 octaves.
over a range of +/-4 octaves.
[F4 (Reverb Level)]
Reverb level of the RPS part
MC-909_Ref_e.book 29 ページ ２００５年３月１日 火曜日 午後３時２９分