Manualsbrain.com
  1. 份说明书
  2. 个品牌
  3. Roland
  4. V-Synth
  5. 用户手册

Roland V-Synth 用户手册

下载
页码 共 180
57
Creating and Editing Samples (Sample Mode)
Creating and Editing Samples (Sample Mode)
3.
Select the location (sample number) that you wish to 
sample.
Move the cursor to the desired sample. Normally, you will select 
a sample that has no wave; i.e., a sample number whose name is 
“NO SAMPLE.”
In this screen you can use the following functions.
• Select a sample by directly touching it.
• Change the number in steps of eight by pressing [
][
].
• Change the number in steps of one by touching <▲><▼> 
located beside the sample list, by pressing [
][
][INC/
+][DEC/-], or by turning the VALUE dial.
• Scroll the sample list by dragging the scroll bar located beside 
the sample list up or down.
• Move to the number 001 sample by touching <Top>.
• Move to the number 999 sample by touching <End>.
• Display information on the currently selected sample by 
• Audition the currently selected sample by touching <Prevw>.
• When you touch <Search Empty>, you will jump to the “NO 
SAMPLE” sample number that follows the current sample 
number.
4.
Touch <Sampling>.
The SAMPLING Template screen appears.
fig.04-02_50
5.
Touch <TMPL 1>–<TMPL 8> to select a sampling template.
If you want to modify the settings of the selected sampling 
template, perform the following steps 6–8.
6.
Touch one of the tabs displayed at the bottom of the screen 
to access the corresponding setting screen.
For details on each parameter, refer to the page references given.
7.
In each setting screen, touch the touch panel to set the 
parameters.
For details on operations in the touch panel, refer to 
8.
To set the value of a parameter, move the cursor to the value 
box of the parameter that you want to edit. Then adjust the 
value by turning the VALUE dial or by using [INC/+] [DEC/-]. 
You can also adjust the value by dragging on the touch 
screen.
9.
Adjust the sampling level.
Adjust the volume of the device that is producing the sound.
When sampling from the INPUT jacks, adjust the level by 
turning the front panel INPUT knob or setting the rear panel 
GAIN switch.
10.
Touch <START> to start sampling.
The way in which sampling will start depends on the Trigger 
Mode setting in the SAMPLING General screen, as follows.
If “MANUAL” is selected, sampling will start after a count of the 
number of measures specified by the metronome Count-In 
setting.
If “MIDI” is selected, sampling will wait for the sequencer to 
start (system realtime message: FA). Sampling will begin when 
the sequencer start message is received.
If “LEVEL” is selected, sampling will wait for an input signal. 
Sampling will begin when the input signal exceeds the level 
specified by Trigger Level (p. 61).
If “NOTE” is selected, Sampling will begin when you play the 
keyboard or note message is received.
If you have selected “MIDI” or “LEVEL,” you can touch 
<START> once again to begin sampling without waiting for the 
sequencer to start or the input signal to be received.
In the SAMPLING window, “Remain Time” indicates the 
remaining time (in seconds) available for sampling.
If memory becomes full, sampling will be halted. If this occurs, 
delete unneeded samples from memory (p. 60).
11.
When you are finished sampling, touch <STOP>.
The display will indicate “COMPLETED!” Touch <PREVIEW> 
to hear the sound that you sampled, and check whether the 
sample was recorded as you wish.
12.
Operations from this point will depend on what you want to 
do.
<Cancel>: Discard the sample that you just recorded, and return 
to the SAMPLING Template screen.
<Decide>: Finalize the sample that you just recorded, and 
register it in the sample list.
<RETRY>: Discard the sample that you just recorded, and 
sample once again.