Roland TD-6 用户手册

Model TD-6

Version 1.00

Feb. 13, 2001

◆

■

*

Following Channel Voice Messages can be recorded in SETUP/MIDI PART/
Part CH.

●

Status

2nd byte

3rd byte

8nH

kkH

vvH

9nH

kkH

00H

n = MIDI channel number:

0H - FH (ch.1 - ch.16)

kk = note number:

00H - 7FH (0 - 127)

vv = note off velocity:

00H - 7FH (0 - 127)

*

Only the channel assigned to the backing part can be received.

*

The Velocity Values of Note Off message are ignored.

*

When recording, this is recorded in the sequencer data itself.

●

Status

2nd byte

3rd byte

9nH

kkH

vvH

n = MIDI channel number:

0H - FH (ch.1 - ch.16)

kk = note number:

00H - 7FH (0 - 127)

vv = note on velocity:

00H - 7FH (0 - 127)

*

A channel which is assigned to the drum kit part will receive only the note 
numbers which are specified by the drum kit.

*

A channel which is assigned to the percussion part will receive only the note 
numbers which are specified by the percussion set.

*

When recording, this is recorded in the sequencer data itself.

●

Status

2nd byte

3rd byte

AnH

kkH

vvH

n = MIDI channel number:

0H - FH (ch.1 - ch.16)

kk = note number:

00H - 7FH (0 - 127)

vv = Value:

00H - 7FH (0 - 127)

*

A channel which is assigned to the drum kit part will receive only the note 
numbers which are specified by the drum kit.

*

If the value is greater than 40H (64), the decay of the note sounded by the 
received note number will be shortened.

*

Not recorded in the sequencer.

●

❍

Status

2nd byte

3rd byte

BnH

00H

mmH

BnH

20H

llH

n = MIDI channel number:

0H - FH (ch.1 - ch.16)

mm = Bank number MSB:

00H - 7FH (bank.1 - bank.128)

ll = Bank number LSB:

processed as 00H

*

Not Received when SETUP/MIDI COMMON/Rx PC Sw is set to "OFF".(Initial 
Value is ON)

*

Bank select processing will be suspended until a program change message is 
received.

*

Only the channel assigned to the backing part can be received.

*

Not recorded in the sequencer.

❍

Status

2nd byte

3rd byte

BnH

04H

vvH

n = MIDI channel number:

0H - FH (ch.1 - ch.16)

vv = Control value:

00H - 7FH (0 - 127)

*

Only the channel assigned to the drum kit part can be received.

*

When recording, this will be recorded as PEDAL CC data in the sequencer data 
itself.

❍

Status

2nd byte

3rd byte

BnH

06H

mmH

n = MIDI channel number:

0H - FH (ch.1 - ch.16)

mm = The value of the parameter specified by RPN.

*

Only the channel assigned to the backing part can be received.

*

Not recorded in the sequencer.

On the normal mode of TD-6, RPN can be used to modify the following 
parameters.
RPN

Data entry

MSB LSB

MSB LSB

Explanation

00H 00H

mmH ---

Pitch Bend Sensitivity
mm: 00H - 18H (0 - 24 semitones)
LSB: ignored (processed as 00H)
specify up to 2 octaves in semitone steps

7FH 7FH

--- ---

RPN null
set condition where RPN is unspecified. The 
data entry messages after set RPN null will 
be ignored.(No Data entry messages are 
required after RPN null).
Settings already made will not change.
MSB,LSB of data entry:ignored

❍

Status

2nd byte

3rd byte

BnH

07H

vvH

n = MIDI channel number:

0H - FH (ch.1 - ch.16)

vv = Volume:

00H - 7FH (0 - 127)

*

Volume messages are used to adjust the volume balance of each part.

*

Only the channel assigned to the percussion part and the backing part can be 
received.

*

Not recorded in the sequencer.

❍

Status

2nd byte

3rd byte

BnH

0AH

vvH

n = MIDI channel number:

0H - FH (ch.1 - ch.16)

vv = Pan:

00H - 40H - 7FH (Left - Center - Right)

*

Only the channel assigned to the backing part can be received.

*

Not recorded in the sequencer.

❍

Status

2nd byte

3rd byte

BnH

40H

vvH

n = MIDI channel number:

0H - FH (ch.1 - ch.16)

vv = Control value:

00H - 7FH (0 - 127) 0-63 = OFF, 64-127 = ON

*

Only the channel assigned to the backing part can be received.

*

When recording, this is recorded in the sequencer data itself.