Roland XV-5080. 用户手册
174
Chapter 6 Creating Rhythm Sets
Time4 (Pitch Envelope Time 4 Velocity
Sensitivity)
Sensitivity)
Range:
-63– +63
Use this parameter when you want keyboard playing
dynamics (velocity) to affect T4 (Time 4) of the pitch envelope.
With higher settings, the T4 value will change more
significantly depending on whether you release the key slowly
or quickly. With positive (+) settings, greater keyboard
velocity will reduce the T4 setting. With negative (-) settings,
greater keyboard velocity will increase the T4 setting.
dynamics (velocity) to affect T4 (Time 4) of the pitch envelope.
With higher settings, the T4 value will change more
significantly depending on whether you release the key slowly
or quickly. With positive (+) settings, greater keyboard
velocity will reduce the T4 setting. With negative (-) settings,
greater keyboard velocity will increase the T4 setting.
RHYTHM WG WMT Vel Range page
([RHYTHM] - [F2 (WG)] - [F4 (V.Range)])
([RHYTHM] - [F2 (WG)] - [F4 (V.Range)])
fig.06-011.e_70
Velocity Control
Switch
Determines whether Velocity range will be recognized (ON),
or ignored (OFF). When set to RANDOM, the Wave will
sound randomly, regardless of any Velocity messages.
or ignored (OFF). When set to RANDOM, the Wave will
sound randomly, regardless of any Velocity messages.
L.F (WMT Velocity Fade Width Lower)
Range:
0–127
Determines what will happen to the Tone’s level when the
Tone is played at a velocity lower than its specified velocity
range. Higher settings result in a more gradual change in
volume. If you don’t want notes played outside the specified
velocity range to be heard at all, set this to 0.
Tone is played at a velocity lower than its specified velocity
range. Higher settings result in a more gradual change in
volume. If you don’t want notes played outside the specified
velocity range to be heard at all, set this to 0.
fig.06-012.e
V.L (WMT Velocity Range Lower)
Range:
1–UPPER
Specifies the highest limit of playing dynamics (key velocity)
which will sound the Tone. Make these settings when you
want different Tones to sound in response to notes played at
different strengths.
which will sound the Tone. Make these settings when you
want different Tones to sound in response to notes played at
different strengths.
V.U (WMT Velocity Range Upper)
Range:
LOWER–127
Specifies the highest limit of playing dynamics (key velocity)
which will sound the Tone. Make these settings when you
want different Tones to sound in response to notes played at
different strengths.
which will sound the Tone. Make these settings when you
want different Tones to sound in response to notes played at
different strengths.
* It is not possible to set the Lower value higher than the Upper
value, or the Upper value below the Lower value. If you
attempt to do so, the two values will change simultaneously.
attempt to do so, the two values will change simultaneously.
U.F (WMT Velocity Fade Width Upper)
Range:
0–127
Determines what will happen to the Tone’s level when the
Tone is played at a velocity greater than its specified velocity
range. Higher settings result in a more gradual change in
volume. If you don’t want notes played outside the specified
velocity range to be heard at all, set this to 0.
Tone is played at a velocity greater than its specified velocity
range. Higher settings result in a more gradual change in
volume. If you don’t want notes played outside the specified
velocity range to be heard at all, set this to 0.
Velocity Range
Status of these settings will be displayed.
RHYTHM WG Sample page ([RHYTHM]
- [F2 (WG)] - [F5 (Sample)])
- [F2 (WG)] - [F5 (Sample)])
You can edit the Sample (Wave data) loaded into the SIMM
(memory module).
(memory module).
* These settings cannot be made unless a Sample is being used.
fig.06-013.e_70
Sample
Sampling Freq. (Sampling Frequency)
Displays the original sampling frequency of the loaded
Sample.
Sample.
Original Key
Displays the original key of the loaded Sample.
1
L.Fade value
U.Fade value
Level
Velocity
Upper
Lower