Roland XV-5080. 用户手册
205
Chapter 8 Saving Tones and Other Data You’ve Created
Chap.8
TYPE
BLOCK
ALL
PR-A, B
*1
PERFORM
USER *2
01–64
PR-A, B
01–32
CARD
01–64
*6
PATCH
USER *2
001–128
PR-A–G *3
001–128
CARD
001–128
*5
XP-A–H
*4
RHYTHM
USER *2
1–4
PR-A–G *3
1–2
CARD
1–4
*5
XP-A–H
*4
SYSTEM
CARD
*6
F-LIST
CARD
*6
* 1 Since there are no others, Performances other than PR-A/B
cannot be selected.
* 2 Move data within the User Memory in block units. The
Move destination Patch is overwritten.
* 3 PR-H uses GM data, and cannot be transmitted.
* 4 Depends on the Wave Expansion Board installed
* 5 After designating the file, set the range specifications for the
block being transmitted.
* 6 Specify the file.
* If the number sent exceeds the capacity of the User memory,
then transmission of the data stops the moment the memory is
filled.
filled.
Destination
Set the number at the transfer-destination in "User."
* You cannot select ALL, SYSTEM, or F-LIST.
The following shows the setting procedure.
1. Press [SYSTEM/UTILITY], getting its indicator to start
blinking.
* If the indicator is steadily lit, you are in SYSTEM mode. Press
[SYSTEM/UTILITY] once again, so the indicator is blinking.
2. Press [F6 (Menu)] to select Menu 2.
3. Press [F2 (Xfer)].
4. Press [F2 (to USER)].
5. Press [
]/[
]/[
]/[
] to move the cursor to
the parameter you want to set.
6. Turn the VALUE dial or press [INC] / [DEC] to select the
desired value.
7. Press [F6 (Trans)] to execute the transmission.
* To cancel the operation, press [EXIT].
Protecting the Internal
Memory (Protect)
Memory (Protect)
This feature helps prevent the accidental overwriting of
USER memory to ensure that Patch, Performance or Rhythm
Set data is not accidentally erased.
USER memory to ensure that Patch, Performance or Rhythm
Set data is not accidentally erased.
Internal Write Protect
The Internal Write Protect setting prevents the Write
operation from accidentally overwriting USER memory
locations. When this is set “ON,” the data cannot be written.
Data can be only written when Internal Write Protect is set to
“OFF.” When the XV-5080’s power is turned on, this setting
is automatically turned on, —you will need to turn it off
before writing data to the USER memory. It is also possible to
turn this setting off during the Write procedure.
operation from accidentally overwriting USER memory
locations. When this is set “ON,” the data cannot be written.
Data can be only written when Internal Write Protect is set to
“OFF.” When the XV-5080’s power is turned on, this setting
is automatically turned on, —you will need to turn it off
before writing data to the USER memory. It is also possible to
turn this setting off during the Write procedure.
Exclusive Protect
The Exclusive Protect setting prevents System Exclusive
messages received from an external MIDI device from
rewriting USER memory settings. When this is set “ON,” the
data cannot be written. Data can be only written when
Internal Write Protect is set to “OFF.” When it is set to
“OFF,” data can be rewritten, even if the Internal Write
Protect setting is set to “ON.”
messages received from an external MIDI device from
rewriting USER memory settings. When this is set “ON,” the
data cannot be written. Data can be only written when
Internal Write Protect is set to “OFF.” When it is set to
“OFF,” data can be rewritten, even if the Internal Write
Protect setting is set to “ON.”
The following shows the setting procedure.
1. Press [SYSTEM/UTILITY], getting its indicator to start
blinking.
* If the indicator is steadily lit, you are in SYSTEM mode. Press
[SYSTEM/UTILITY] once again, so the indicator is blinking.
2. Press [F6 (Menu)] to select Menu 1.
3. Press [F5 (Protect)].
The User Memory Protect page will appear.
fig.08-011.e_70
4. Press [
]/[
] to move the cursor to the parameter
you wish to set.
5. Either by rotating the VALUE dial, or by pressing [INC]/
[DEC], select the save destination.