Roland XV-5080. 用户手册
27
Chapter 2 Using the XV-5080 Effects
Chap.2
REV:
The Chorus output is sent only to the Reverb.
fig.02-010.e
M+R:
The Chorus output is sent to the OUTPUT jacks and to
the Reverb.
fig.02-011.e
Chorus Level 0–127
Determines the Chorus output level.
Chorus Output Assign A–D
Selects the pair of OUTPUT jacks to which the Chorus unit’s
stereo output is routed when Chorus Output Select is set to
“MAIN” or “M+R.”
stereo output is routed when Chorus Output Select is set to
“MAIN” or “M+R.”
Pressing [F4 (Chorus)] in the General page calls up the
Chorus page, in which you can make the following settings.
Chorus page, in which you can make the following settings.
• For Type: 1 (CHORUS)
Rate (Chorus Rate) 0.05–10.00 Hz
Adjusts the modulation speed of the chorus effect.
Depth (Chorus Depth) 0–127
Adjusts the modulation depth of the chorus effect.
Feedback (Chorus Feedback) 0–127
Specifies the amount of the chorus effect’s output to be
returned - fed back - to its input. Higher settings will create a
more complex Chorus effect.
returned - fed back - to its input. Higher settings will create a
more complex Chorus effect.
Phase 0–180 degree
Adjusts the spatial spread of the sound.
Pre Delay (Chorus Pre Delay) 0.0–100 ms
Adjusts the delay time from the direct sound until when the
chorus sound is heard.
chorus sound is heard.
Higher settings will make the sound more spacious.
Type (Filter Type)
Selects the type of filter.
OFF:
No filter is used.
LPF:
Frequencies higher than the selected cutoff frequency
value are eliminated.
HPF:
Frequencies lower than the selected cutoff frequency
value are eliminated.
Cutoff freq (Cutoff Frequency) *1
Sets the cutoff frequency when a specific frequency band is
cut off by a filter.
cut off by a filter.
*1 200, 250, 315, 400, 500, 630, 800, 1000, 1250, 1600, 2000,
2500, 3150, 4000, 5000, 6300, 8000 Hz
• For Type: 2 (DELAY)
Center (Delay Center) 200–1000 ms, Note
Sets the delay time for the delay located at the center of the
stereo field.
stereo field.
Left (Delay Left) 200–1000 ms, Note
Sets the delay time for the delay located at the left side of the
stereo field.
stereo field.
Right (Delay Right) 200–1000 ms, Note
Sets the delay time for the delay located at the right side of
the stereo field.
the stereo field.
HF Damp *1
This allows you to reduce, or “damp,” the high-frequency
content of the repeated feedback delays—frequencies above
the selected value will be damped. If you do not want to cut
the high frequencies of the feedback, set this parameter to
BYPASS.
content of the repeated feedback delays—frequencies above
the selected value will be damped. If you do not want to cut
the high frequencies of the feedback, set this parameter to
BYPASS.
*1 200, 250, 315, 400, 500, 630, 800, 1000, 1250, 1600, 2000,
2500, 3150, 4000, 5000, 6300, 8000 Hz, BYPASS
Feedback -98– +98%
Adjusts the amount of delay feedback, controlling the
number of times the delay repeats. With negative (-) values,
the phase of the repeated delays is inverted.
number of times the delay repeats. With negative (-) values,
the phase of the repeated delays is inverted.
Center (Delay Center Level) 0–127
Sets the volume level of the delay located at the center of the
stereo field.
stereo field.
Left (Delay Left Level) 0–127
Sets the volume level of the delay located at the left side of
the stereo field.
the stereo field.
Right (Delay Right Level) 0–127
Sets the volume level of the delay located at the right side of
the stereo field.
the stereo field.
OUTPUT
Chorus Input
Chorus
Reverb
OUTPUT
OUTPUT
Chorus Input
Reverb Input
Chorus
Reverb