Roland VGA-3 用户手册
21
MEMORY
You can store and call up ten knob and button settings on the VGA-3. Additionally, with the use of a foot controller (such as the
optional GFC-50 or FC-200), you can store and call up forty knob and button settings (p. 22).
optional GFC-50 or FC-200), you can store and call up forty knob and button settings (p. 22).
* The settings controlled by the following external devices are also stored to the memory along with knob and button settings.
Foot Switch (EFX ON/OFF, DELAY ON/OFF), Expression Pedal (VOLUME, GK, WAH)
Calling Up Memory
1. Press MEMORY button to select the memory to be
called up.
When the [A/B] button is not lit, the memories
numbered from 1 through 5 can be selected.
numbered from 1 through 5 can be selected.
When the [A/B] button is lit, the memories numbered
from 6 through 10 can be selected.
from 6 through 10 can be selected.
Changing the Memory Settings (Edit)
1. Press memory button to select the memory whose
settings are to be changed.
2. Operate the knobs/buttons.
When you change the knob or button settings, the button
indicator corresponding to the selected memory flashes.
indicator corresponding to the selected memory flashes.
Immediately after you switch memories, the knob
positions may not correspond to the settings stored in
the memory. When you turn a knob, the knob’s
adjustment function is enabled as you approach the
position stored in the memory. If you are not sure of the
setting stored in memory, turn the knob completely to
the left (counterclockwise); the knob’s function is
enabled at that time.
positions may not correspond to the settings stored in
the memory. When you turn a knob, the knob’s
adjustment function is enabled as you approach the
position stored in the memory. If you are not sure of the
setting stored in memory, turn the knob completely to
the left (counterclockwise); the knob’s function is
enabled at that time.
If before the setting is stored the mode is switched to
Manual or Memory, or the power is turned off, all
changes in the settings will be discarded. Whenever
working with important settings, be sure to carry out the
Write procedure.
Manual or Memory, or the power is turned off, all
changes in the settings will be discarded. Whenever
working with important settings, be sure to carry out the
Write procedure.
Storing Knob and Button
Settings to Memory (Write)
Settings to Memory (Write)
1. When you have finished making the knob and/or
button settings, press [WRITE], causing the indicator to
flash.
flash.
2. Press MEMORY button for the memory in which you
want the settings stored.
* If you want to cancel the Write procedure, press [MANUAL].
3. Press [WRITE] once more to carry out the write.
During the write, the [WRITE] indicator flashes rapidly;
the write is completed when the [WRITE] indicator stops
flashing and stays off.
the write is completed when the [WRITE] indicator stops
flashing and stays off.
Confirming the Settings Stored
in Memory (Memory Utility)
in Memory (Memory Utility)
This reproduces the knob positions (settings values) stored in
memory.
memory.
* This function is disabled whenever [MANUAL] is selected.
* During confirmation, the volume and tone are not changed
when any knob other than [MASTER] is rotated.
1. Hold down [TUNER] and press [MANUAL].
* The [TUNER] flashes.
2. Operate the knob for the setting you want to check.
* One of the TUNER meter indicators lights up.
3. While monitoring TUNER meter indicators, rotate the
knob further until the green indicator in the center is lit.
fig.0170
4. Repeat Steps 2 and 3 for any knob you want to check.
5. Press [TUNER] again to complete the confirmation
procedure.
Correspond to the setting
stored in the memory
stored in the memory
Rotate the knob
clockwise
clockwise
Rotate the knob
counterclockwise
counterclockwise
Lit
Lit