Roland XV-3080 用户手册
100
Chapter 4 Creating a Patch
TMT Ctrl Sw (TMT control switch) OFF/ON
This setting determines whether or not the TMT is controlled
by the Matrix Control. When TMT Velocity Control is set to
OFF, turning this parameter on and off is a simple way to
switch between playing all Tones or controlling them with
the Matrix Control, making this an effective tool for
auditioning Tones.
by the Matrix Control. When TMT Velocity Control is set to
OFF, turning this parameter on and off is a simple way to
switch between playing all Tones or controlling them with
the Matrix Control, making this an effective tool for
auditioning Tones.
Bend Range (Pitch bend range) 0–48
This sets the amount of pitch change that will occur when
you move the Pitch Bend lever. The left value specifies the
amount of pitch change that will be applied to the Patch’s
pitch when the lever is moved fully left (or down on some
MIDI controllers). The right value specifies the pitch change
that will occur when the lever is moved fully to the right (or
up). The left value has a range of -48–0 (-4–0 octaves), and the
right value has a range of 0–+48 (0–4 octaves).
you move the Pitch Bend lever. The left value specifies the
amount of pitch change that will be applied to the Patch’s
pitch when the lever is moved fully left (or down on some
MIDI controllers). The right value specifies the pitch change
that will occur when the lever is moved fully to the right (or
up). The left value has a range of -48–0 (-4–0 octaves), and the
right value has a range of 0–+48 (0–4 octaves).
MATRIX CTRL SRC (Matrix control
source)
source)
If you wish to use controllers to control a specific Tone
parameter, you can select the desired controller in this page.
Four control sources can be assigned to each Patch.
parameter, you can select the desired controller in this page.
Four control sources can be assigned to each Patch.
Control 1–4 (Matrix control 1–4 source)
Assign one of the following controllers to Control Source 1–4.
If you wish to use a controller that will apply to all Patches,
or a controller that cannot be directly selected here, select
SYS-CTRL1–4, and then select the controller using the
Control Source 1–4 parameters (SYS CTRL ASSIGN page).
If you wish to use a controller that will apply to all Patches,
or a controller that cannot be directly selected here, select
SYS-CTRL1–4, and then select the controller using the
Control Source 1–4 parameters (SYS CTRL ASSIGN page).
OFF:
a controller will not be used
CC01–CC95:
Contoroller number 1–95 (except CC32)
BENDER
AFTERTOUCH
SYS-CTRL1:
System Control 1
SYS-CTRL2:
System Control 2
SYS-CTRL3:
System Control 3
SYS-CTRL4:
System Control 4
VELOCITY
KEYFOLLOW
TEMPO
LFO1
LFO2
PITCH-ENV:
Pitch Envelope
TVF-ENV:
TVF-Envelope
TVA-ENV:
TVA-Envelope
MATRIX CTR1–4 (Matrix control 1–4)
This selects the parameters to be controlled by Matrix
Control Source 1–4 and the Sens settings, as well as the
specific Tones whose parameters you wish to control. Up to
four destination parameters can be selected for each
controller and controlled simultaneously.
Control Source 1–4 and the Sens settings, as well as the
specific Tones whose parameters you wish to control. Up to
four destination parameters can be selected for each
controller and controlled simultaneously.
The upper line of the display shows the Control Source
selected in the MATRIX CTRL SRC page.
selected in the MATRIX CTRL SRC page.
DEST1–4 (Destination 1–4)
Dest:
This selects a parameter to be controlled.
Sns:
This adjusts the amount of change that will occur in
response to controller changes. Negative (-) values invert the
change. For LFO rates, negative (-) values slow down the
LFO, and positive (+) values will speed it up.
change. For LFO rates, negative (-) values slow down the
LFO, and positive (+) values will speed it up.
Tone:
This selects the Tone to which the two previous
parameter settings are applied. “o” turns signifies that the
Tone is selected for control, “_” that it is not selected, and
“R” that the change being applied is inverted when applied
to this Tone.
Tone is selected for control, “_” that it is not selected, and
“R” that the change being applied is inverted when applied
to this Tone.
Effect Settings (EFFECTS)
Refer to “Adjusting Effect Settings in Patch mode” (p. 21).
Saving Patches You Create
Refer to “Saving Patches” (p. 122).
Copying the Settings of
Another Patch (Patch Tone
Copy)
Another Patch (Patch Tone
Copy)
Tone settings from a Patch can be copied to the currently
selected Patch. You can use this feature to make the Patch
editing process faster and easier.
selected Patch. You can use this feature to make the Patch
editing process faster and easier.
1. Make sure that a Patch is selected.
2. Press [UTILITY] to make its indicator light.
3. Press [
] / [
] to select the UTIL 1 page.