Roland XV-3080 用户手册
138
Chapter 9 Examples of Applications Using the XV-3080
Using a Pedal Switch to Modify
the Rotary Speed of the Rotary
Effect
the Rotary Speed of the Rotary
Effect
1. Connect a pedal switch (DP-2, DP-6, etc.) to your external
device (MIDI keyboard, etc.).
2. Set the pedal switch of the external MIDI device to
generate FOOT-TYPE (CC4) control-change messages.
* To learn how to set up the pedal switch, refer to the external
MIDI device’s owner’s manual.
3. Select PR-A:050 Perky B on the PATCH PLAY page.
This Patch uses ROTARY as its Multi-Effect.
4. Go to the PATCH MFX CTRL page ([PATCH]-
[EFFECTS]) and set 1:Source to FOOT-TYPE.
5. Set Destination to SPEED, and Sens to +63.
6. When you wish to speed up the rotary effect, press the
pedal switch. Release the pedal switch to slow down the
rotary effect.
rotary effect.
Playing Phrase Loops at a
System’s Tempo
System’s Tempo
An optional Wave Expansion Board can contain Patches
based on waveforms that are timed – in BPM – phrase loops.
You can play these phrase loops in sync with the System
Tempo.
based on waveforms that are timed – in BPM – phrase loops.
You can play these phrase loops in sync with the System
Tempo.
1. On the PATCH PLAY page, select a Patch that uses a
phrase loop.
2. Set Clock Source (PATCH TEMPO page ([PATCH]-
[COMMON])) to SYSTEM.
3. Call up the WAVE page ([PATCH]-[WAVE]).
Press TONE SELECT [1]–[4] to find the Tone that uses
phrase-loop waveforms.
phrase-loop waveforms.
The waveform name appears at the right side of the display
(the upper line shows the left side of the stereo wave; the
lower line shows its right side). Waveform names that have a
BPM number in the first part of the name (such as
“132:WAVE NAME”) are phrase loop waveforms.
(the upper line shows the left side of the stereo wave; the
lower line shows its right side). Waveform names that have a
BPM number in the first part of the name (such as
“132:WAVE NAME”) are phrase loop waveforms.
4. Go to the TONE DELAY page ([PATCH]-[WAVE]).
5. Set Time to 0.
If you select a value other than 0, a delay will be applied, and
you will not be able to play the Patch normally.
you will not be able to play the Patch normally.
6. Set Clock Source (SYSTEM SETUP page ([SYSTEM]-
[SETUP])) to INT.
* When Clock Source is set to MIDI, you can synchronize the
phrase loop to the tempo of an external MIDI device.
7. When the System Tempo (SYSTEM SETUP page
([SYSTEM]-[SETUP])) changes, the speed of the phrase
loop changes along with it.
loop changes along with it.
* The phrase loop will sound at the system’s tempo regardless of
which key you press. The settings for pitch and FXM will be
ignored.
ignored.
Changing the Part Settings
from an External MIDI
Device
from an External MIDI
Device
By sending Control Change messages for different Part
settings, including volume, panning, and pitch, you can
change these settings from an external MIDI device
connected to the XV-3080. This lets you control fade-ins and
fade-outs, open and close filters, and exercise other controls
in real time from the external MIDI device.
settings, including volume, panning, and pitch, you can
change these settings from an external MIDI device
connected to the XV-3080. This lets you control fade-ins and
fade-outs, open and close filters, and exercise other controls
in real time from the external MIDI device.
The parameters that can be used for changing the settings
and the Control Change messages that can be used to change
the values are shown below.
and the Control Change messages that can be used to change
the values are shown below.
* For more detailed information about Control Change
* To changing multi-effects, reverb, or chorus effects from an
• Level: Controller number 7
• Pan: Controller number 10
• Portament: Controller number 65 (Portamento switch),
Controller number 5 (Portamento time)
Changing Sounds’ Attack and Release Time (p.
174)
174)
• Rel: Controller number 72
• Atk: Controller number 73