Roland Fantom-Xa 用户手册
102
Sampling
1.
Hold down [SHIFT] and press [MIX IN].
The INPUT SETTING screen appears.
2.
When using the Input Effect, add a check mark (
✔
) by
pressing [F5 (In FX SW)] to turn it on.
3.
Press [F6 (In FX SETUP)].
The INPUT FX SETUP screen appears.
fig.InFxSetup
4.
Press
or
to select the parameter.
5.
Turn the VALUE dial, or press [INC] /[DEC] to set the value.
6.
Press [EXIT] to return to the previous screen.
Input Effect Parameters
*
In the In FX SETUP screen, the Realtime Control knobs (C1–C4) can
be used to edit the MFX parameters.
be used to edit the MFX parameters.
Input Effect Setup Settings
Cautions when using a microphone
983
Howling could be produced depending on the location of
microphones relative to speakers. This can be remedied by:
microphones relative to speakers. This can be remedied by:
1.
Changing the orientation of the microphone.
2.
Relocating microphone at a greater distance from speakers.
3.
Lowering volume levels.
Parameter
Value
Explanation
(Type)
1–6
Input effect type
1: Equalizer
Adjusts the tone of the low-frequency and high-frequency ranges.
Low Freq
Low Freq
200, 400 Hz
Center frequency of the low-fre-
quency range
quency range
Low Gain
-15– +15 dB
Amount of low-frequency boost/
cut
cut
High Freq
2000, 4000,
8000 Hz
8000 Hz
Center frequency of the high-fre-
quency range
quency range
High Gain
-15– +15 dB
Amount of high-frequency boost/
cut
cut
2: Enhancer
Modifies the harmonic content of the high-frequency range to add
sparkle to the sound.
Sens
sparkle to the sound.
Sens
0–127
Depth of the enhancer effect
Mix
0–127
Volume of the harmonics that are
generated
generated
3: Compressor
Restrains high levels and boosts low levels to make the overall vol-
ume more consistent.
Attack
ume more consistent.
Attack
0–127
Time from when the input ex-
ceeds Threshold until the volume
begins to be compressed
ceeds Threshold until the volume
begins to be compressed
Threshold
0–127
Volume at which compression
will begin
will begin
Post Gain
0– +18 dB
Level of the output sound
4: Limiter
Compresses the sound when it exceeds a specified volume, to
keep distortion from occurring.
Release
keep distortion from occurring.
Release
0–127
Time from when the input falls
below Threshold until compres-
sion ceases
below Threshold until compres-
sion ceases
Threshold
0–127
Volume at which compression
will begin
will begin
Post Gain
0– +18 dB
Level of the output sound
5: Noise Suppressor
Suppresses noise during periods of silence.
Threshold
Threshold
0–127
Volume at which noise suppres-
sion will begin
sion will begin
Release
0–127
Time from when noise suppres-
sion begins until the volume
reaches zero
sion begins until the volume
reaches zero
6: Center Canceler
Removes the sounds that are localized at the center of the stereo
input. This is a convenient way to eliminate a vocal.
Ch Balance
input. This is a convenient way to eliminate a vocal.
Ch Balance
-50– +50
Volume balance of the left and
right channels for removing the
sound
right channels for removing the
sound
Range Low
16–15000 Hz
Lower frequency limit of the band
to be removed
to be removed
Range High
16–15000 Hz
Upper frequency limit of the band
to be removed
to be removed
Fantom-Xa_e.book 102 ページ ２００４年１０月２２日 金曜日 午後２時３分