Roland Fantom-Xa 用户手册
78
Creating a Performance
The Fantom-Xa lets you assign the parameters that will be affected
when you operate the realtime control knobs, assignable switches, D
Beam, pitch bend, or modulation lever. This lets you modify the
sound in a variety of ways by operating the controllers.
when you operate the realtime control knobs, assignable switches, D
Beam, pitch bend, or modulation lever. This lets you modify the
sound in a variety of ways by operating the controllers.
1.
Access the PERFORM LAYER screen, and select the
2.
Press [F3 (CONTROL)].
The CTRL SETTING screen appears.
fig.CtrlSettingPfm
3.
Press [F1]–[F5] and/or
to select the parameter.
4.
Use the VALUE dial or [INC] [DEC] to change the value.
5.
Repeat steps
3
–
5
to set each parameter you want to edit.
6.
Press [WRITE] to save the changes you’ve made.
If you do not wish to save changes, press [EXIT] to return to
the PERFORM LAYER screen.
the PERFORM LAYER screen.
*
Settings for the Solo Synth are saved for system settings. Press [F6
(WRITE)] to execute the write operation.
(WRITE)] to execute the write operation.
If you return to the PERFORM LAYER screen without saving,
an “*” will be displayed at the left of the Performance group.
an “*” will be displayed at the left of the Performance group.
If you turn off the power or select a different sound while the
display indicates “*,” your edited Performance will be lost.
display indicates “*,” your edited Performance will be lost.
[F1 (KNOB)]
[F2 (SWITCH)]
[F3 (TEMPO)]
Recommended Tempo
If you want the sequencer tempo to change when you switch
Performances, specify the tempo that will follow this change. This
setting is valid when the Seq Tempo Override parameter is “ON.” In
order to enable this setting, turn on the Tempo Override parameter
(p. 200).
Performances, specify the tempo that will follow this change. This
setting is valid when the Seq Tempo Override parameter is “ON.” In
order to enable this setting, turn on the Tempo Override parameter
(p. 200).
VALUE:
20–250
*
This value is specified independently for each performance. This means
that when you switch performances, the tempo setting of the Fantom-
Xa will change.
that when you switch performances, the tempo setting of the Fantom-
Xa will change.
*
The sequencer tempo will be overwritten to the new tempo when you
switch performances.
switch performances.
[F4 (DBEAM)]
[F5 (DB SYN)]
You can change controller switch on/off settings for each patch in
the performance.
the performance.
1.
In the CONTROL SETTING screen, press [F6 (CTRL SW)].
The CONTROL SWITCH screen appears.
fig.CtrlSwPfm
2.
Use [CURSOR] to select the parameter.
3.
Use the VALUE dial or [INC] [DEC] to change the setting.
4.
Repeat steps 2–3 to set each parameter you want to edit.
5.
Press [F6 (EXIT)] to return to the previous screen.
Settings for the Realtime
Controllers and D Beam
Controller
Controllers and D Beam
Controller
Control Switch Settings
[F6 (CTRL SW)]
[F6 (CTRL SW)]
Parameter
Value
Explanation
PB
OFF,
ON (
ON (
✔
)
For each part, specify whether MIDI
Pitch Bend messages will be transmit-
ted.
Pitch Bend messages will be transmit-
ted.
Mod
For each part, specify whether MIDI
Modulation messages will be transmit-
ted.
Modulation messages will be transmit-
ted.
Hold
For each part, you can specify whether
control messages from a pedal connect-
ed to the HOLD PEDAL jacks will be
transmitted.
control messages from a pedal connect-
ed to the HOLD PEDAL jacks will be
transmitted.
Ctrl
For each part, you can specify whether
control messages from a pedal connect-
ed to the CONTROL PEDAL jacks will
be transmitted.
control messages from a pedal connect-
ed to the CONTROL PEDAL jacks will
be transmitted.
D Beam
Specifies whether each part will be con-
trolled by the D Beam.
trolled by the D Beam.
Knob 1–4
Specifies whether each part will be con-
trolled by the REALTIME CONTROL
knob 1–4.
trolled by the REALTIME CONTROL
knob 1–4.
Fantom-Xa_e.book 78 ページ ２００４年１０月２２日 金曜日 午後２時３分